manualshive.com logo in svg

GHM GREISINGER GFTH 200 Kal, Руководство по эксплуатации

Поделиться
Скачать
GHM GREISINGER GFTH 200 Kal Скачать руководство пользователя страница 21

GMH 3331

Operation and maintenance | 7

B-H77.0.01.DB2-1.0

21 / 32

7 Operation and maintenance

7.1 Operating and maintenance notices

 NOTE

Plugs and sockets must be protected from soiling.

 NOTE

If the product is stored at a temperature above 50 °C, or is not used for an extended
period of time, the batteries must be removed. Leaks from the batteries are avoided as
a result.

 NOTE

The product, measuring sensor and temperature probe must be handled with care and
used in accordance with the technical data. Do not throw or strike. Contaminants can
influence the measurement negatively. Use of an unsuitable measuring sensor or tem-
perature probe can damage said devices or the product.

 NOTE

The product must be switched off to change the measuring sensor, the temperature
probe, electrode, interface or mains adaptor. It must not be disconnected by pulling
the cable; pull the plug only.

7.2 Battery

7.2.1 Battery indicator

If the 

BAT

 display text appears in the main display, the battery voltage is no longer ad-

equate for operation of the product. The battery is fully depleted.

If 

BAT

 appears in the display with a warning triangle, the battery is low and should be

replaced soon. However, the device will still operate for a certain length of time.

7.2.2 Changing battery

Description

Proceed as follows to replace the batteries.

Prerequisites

– The product is switched off.

Instruction

1. Open the cover of the product by carefully pushing it back and away from the

product.

2. Pull the battery out of the compartment and disconnect it.

3. Ensure correct polarity when replacing the battery!

4. Insert the battery in the compartment. Then position the cover correctly and slide it

in until it engages.

Outcome of an action

The product is now ready for use again.

Содержание GREISINGER GFTH 200 Kal

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды