manualshive.com logo in svg

GHM GREISINGER G 1610, Компактное руководство, Страница: 22 / 26

Поделиться
Скачать
GHM GREISINGER G 1610 Скачать руководство пользователя страница 22

7 | Error and system messages

 

G 1610 

 

22 / 26 

 

B-H86.0.2X.DK2-3.0 

7 

Error and system messages 

Display

 

Meaning

 

Possible

 

causes

 

Remedy

 

----

 

Sensor cable 
defect 

Sensor or device 
defect 

Measuring range 
exceeded/undercut 

Cable breakage 
 

Sensor or device 
defect 

Measurement outside 
permissible range 

Send in for repair 
 

Send in for repair 
 

Stay within allowable 
measurement range 

No display, 
unclear characters 
or no response 
when buttons are 
pressed 

Battery depleted 

System error 

Device is defective 

Battery depleted 

Error in the device 

Replace battery 

Send in for repair 

BAT 

Battery depleted 

Battery depleted 

Replace battery 

ERR.1 

Measuring range 
exceeded 

Measurement too high 
 

Faulty calibration 

Electrode or device 
defect 

Stay within allowable 
measurement range 

Perform calibration 

Check electrode 

Send in for repair 

ERR.2 

Measuring range is 
undercut 

Measurement too low 

Electrode or device 
defect 

Check electrode 

Send in for repair 

SYS ERR 

System error 

Error in the device 

Switch device on/off 

Replace batteries 

Send in for repair 

 

(AL ERR.2

 

Slope is too low 

Incorrect oxygen 
reference 

Electrode contaminat-
ed or defective 

Perform calibration in 
damp environmental air 

Maintain the electrode 

(AL ERR.3

 

Slope is too high 

Incorrect oxygen 
reference 

Electrode contaminat-
ed or defective 

Perform calibration in 
damp environmental air 

Maintain the electrode 

Содержание GREISINGER G 1610



























Отзывы:

Нет отзывов