background image

E40.0.5X.6C-01 

Operating Manual EASY

LOG

 80IMP… 

page 14 of 16 

Alarm function 

alarm points selectable within the display range and alarm 

delay adjustable from 0 to 500 min 

Nominal temperature  

25 °C 

Operating temperature 

-25.0 … +60.0 °C 

Storage temperature 

-30.0 … +70.0 °C 

Housing 

ABS housing, transparent screen made of polyester 

  Dimensions 

48,5 × 48,5 × 35,5 mm  (L × W × D) 

without sensor cable, angle-type plug and EASYBus plug. 

  Protection rate  

IP65 (IP00 for open cable ends of connection cable) 

Electric connection 

(for input signals)

 

approx. 0.5 m connection cable. 

cable assignment: red = ; transparent = signal – 

Directives and standards

 

The instruments confirm to following European directives: 

 

2011/65/EU  RoHS  

  2014/30/EU  EMV directives 

Applied harmonized standards: 

  EN 50581 : 2012 

  EN 61326-1:2013  emissions level: class B 

   

 

 

emi immunity according to table 1  

   

 

 

additional error:  < 1% 

 

Note:   When connecting long leads adequate safety measures 

against voltage surges have to be taken.

 

10.  Decommissioning, reshipment and disposal 

 

10.1  Reshipment 

 

All devices returned to the manufacturer have to be free of any residual of 

measuring media and other hazardous substances. Measuring residuals at 

housing or probe may be a risk for persons or environment. 

 

Use an adequate transport package for reshipment, especially for fully functional 

devices. Please make sure that the device is protected in the package by 

enough packing materials. 

10.2  Disposal instructions 

 

The device must not be disposed in the unsorted municipal waste!  

Send the device directly to us (sufficiently stamped), if it should be disposed.  

We will dispose the device appropriate and environmentally sound. 

 

 

Содержание GREISINGER EASYLOG 80IMP Series

















Отзывы: