manualshive.com logo in svg

GFS Performer ES, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
GFS Performer ES Скачать руководство пользователя страница 36

General service procedures

This section contains procedures that can be performed as needed to correct problems or as directed by
the preventive maintenance schedules in “Daily maintenance” (page 16), Weekly maintenance, “Monthly
maintenance” (page 26), and “Yearly maintenance” (page 29).

Replace a defective bulb

NOTE
Perform this task if a specific light bulb is burned out or is noticeably dimmer than the other bulbs.

WARNING
Before servicing, lockout/tagout the main electrical service to the booth.

1.

Remove any protective covering from the light whose bulb is being replaced:

• If you use Lens Protector: Remove the Lens Protector plastic sheet.

• If you use Booth Shield: Score around the light and peel off the Booth Shield covering.

2.

Removing the eight (6 mm x 20 mm) cap-head screws that secure the light cover to the panel.

NOTE
Make sure to support the light cover when removing the last screws.

3.

Pull the light cover away from the panel and place the cover in a safe place.

NOTE
If you do not use a protective covering on the lights, you might have to clean overspray from the light
cover and panel before you can remove the light cover.

4.

Rotate the tube 90 degrees to free the bulb from the lamp holder and remove the burned-out light bulb.

NOTE
Two spring-loaded holders keep the tube in place.

5.

Replace the bulb by pushing one end of the new tube into one of the two spring-loaded holders, sliding
the other end into the other holder, and then rotating the tube 90 degrees to lock in place.

6.

Replace the light cover, ensure the alignment of the interlocking safety switch, and then secure it with
the eight (6 mm x 20 mm) cap-head screws.

7.

Once all light covers have been installed and the booth is safe to operate, remove the lockout/tagout
and apply power to the booth.

8.

Verify that all light bulbs illuminate.

9.

If applicable, apply a fresh protective covering over the light.

Replace the protective light covering

Scope:

• If brightness is diminished but you do not use a protective covering on the lights, use a non-ferrous, non-

sparking scraper to remove overspray buildup from the lights.

Service and maintenance

Global Finishing Solutions

36

239-062 rev 5

Содержание Performer ES


















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды