gfm Peakanalyzer Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 40

gfm Peakanalyzer Скачать руководство пользователя страница 27

Peakanalyzer Installation Manual Version 2.6

27

2.3.19.2 Connection of EtherCAT-Coupler of type EK1100 for LAN cable

The  EtherCAT-Coupler  of  type  EK1100  is  used  for  the  EtherCAT  signal  transmission  in  an
Ethernet network (100BASE-TX). The EtherCAT-Coupler of type EK1100 connects a steel box
with distributed Peakanalyzer  terminals of type ELXXXX via LAN to a central Peakanalyzer
base module.

Picture 16: View of EtherCAT-Coupler EK1100 for LAN-cable

A  Peakanalyzer  station  that  is  distributed  in  the field  consists  of  a  coupler  of  type  EK1100,
several  EtherCAT  terminals,  an  end  cap  and  a  power  supply.  The  coupler  transforms  the
telegrams from the Ethernet-100BASE-TX to the E-Bus representation.

The connection to the central Peakanalyzer base module is done via the IN interface on the
coupler. The LAN cable must have the same label as the coupler input IN. The RJ45 socket
OUT below the IN socket can be used to optionally branch a further Peakanalyzer station. The
outgoing EtherCAT branch must be also labeled on the corresponding LAN cable. The
incoming and outgoing branches are also labeled on the coupler and the junction. The schema
of the labels is described in chapter 2.3.19.

The power supply terminal labeled with X5 has to be connected to a power supply source
according to chapter 2.3.1, 2.3.2 and 2.3.13.

«
...
25
26
27
28
29
...
»

Содержание Peakanalyzer









































Отзывы:

Нет отзывов