GESTRA RHOMBUSline MK 45 A-1 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 28

background image

17

Troubleshooting

Fault

Cause

Remedy

The steam trap is cold or only
hand-hot.

The shut-off valves for
condensate inlet or outlet are
closed.

Open the shut-off valves.

The condensate inlet or outlet
is dirt clogged.

Clean the pipes.
Clean the equipment.

The steam trap is blowing off
live steam.

The membrane regulator
capsule and the nozzle insert
are dirty.
There are dirt deposits in the
equipment.

Clean the membrane regulator capsule
and the nozzle insert.
Clean the strainer and the equipment.
Replace the membrane regulator capsule
and the nozzle insert.

The membrane regulator
capsule and the nozzle insert
are worn down.
The seat is leaking.

Replace the membrane regulator capsule
and the nozzle insert.

The bypass is open.

Close the bypass.

«
...
15
16
17
18
19
...
»

Содержание RHOMBUSline MK 45 A-1





























Отзывы:

Нет отзывов

Похожие инструкции для RHOMBUSline MK 45 A-1

Бренд: Taber Страницы: 27

Бренд: Campden instruments Страницы: 8

Бренд: Febco Страницы: 12

Бренд: Yetter Страницы: 16

Бренд: JB-Lighting Страницы: 60

Бренд: Unex Страницы: 5

Бренд: Tabi Страницы: 8

Бренд: Dabi Atlante Страницы: 102

BODY ARMOR PRO TERM

Бренд: Darco Страницы: 6

Бренд: tayco Страницы: 111

Бренд: IDEAL Networks Страницы: 60

Бренд: IceCure Страницы: 104

Бренд: Launch Страницы: 3

Бренд: Launch Страницы: 43

Бренд: Launch Страницы: 8

Бренд: Launch Страницы: 67

Бренд: Launch Страницы: 55

Бренд: LAUNCH TECH Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды