P.52
P.53
Setting up & Installation
Note:
we recommend you keep the screws to immobilise the machine for future transit.
The Manufacturers will not be responsible for any possible damage to the machine caused by not
following the rules relating to releasing the mechanism. The user is responsible for all costs of installation.
Water connection
The appliance must be connected to the water mains using new hose-sets.
The old hose-sets should not be re-used.
The machine has an inlet hose with 3/4” B.S.P threaded end connection to attach
between the threaded connector on the appliance and the cold water supply.
Note:
This machine only uses cold water; therefore only one hose is needed to connect to
the cold water supply. Do not connect to the hot supply. Cold fill is an energy
efficient system. Only the water required for the washing is heated. There is no loss
of heat in the pipeline from a hot water tank or boiler to the machine.
Note:
It is advisable to turn off the tap after each wash to isolate the washing machine from the water supply.
For the washing machine to function properly the terminal end of the discharge hose (mouth) must be at a
minimum of 50 cm and a maximum of 85 cm from the ground.
Min 大於 50 cm
Max 小於 85 cm
+2.6 mt Max 最大
Max 最大 100 cm
min 4 cm
Setting up & Installation
1
Remove the polystyrene base and place the machine near its permanent position (diagram 1).
2
Carefully cut through the hose retaining clip at the rear of the appliance (diagram 2).
3
Remove the 4 fixing screws marked (A) and remove the 4 spacers marked (B) (diagram 3).
4
Cover the 4 holes using the caps provided in the instruction booklet pack (diagram 4).
WARNING:
DO NOT LEAVE THE PACKAGING WITHIN REACH OF CHILDREN AS IT IS A POTENTIAL SOURCE OF DANGER.
Apply the insulation sheet of corrugated material to the base as shown.
Use the 4 feet to level the machine with the floor:
a) Turn the nut clockwise to release the screw adjuster on the foot.
b) Rotate the foot to raise or lower it until it stands firmly on the A ground.
c) Lock the foot in position by turning the nut
anti-clockwise until it comes up against the bottom of the machine.
1
2
3
4
A
B
C
Содержание WSR-1712
