安裝說明
Installation Instructions
安裝說明
Installation Instructions
P.8
P.9
I. Room Ventilation
Give the kitchen the amount of air required for regular
gas combustion and for the room to keep well-
ventilated. Air must naturally flow through permanent
opening in the walls of the room, in
strict compliance with any local regulation in force.
II. Gas Connection
Attention
According to the Gas Safety Regulations of Hong
Kong, any gas installation works including the
installation of appliances and connection tubing,
must be undertaken by registered gas installers who
are registered for that appropriate classes and be
employed by registered gas contractors.
Use approved gas tubing bearing EMSD approval
marking (such as :
機電工程署批准
EMSD
APPROVAL GTXXXX) for connection to appliances,
or other appropriate methods accepted by EMSD.
When installing built-in gas hob on top of stove cabinet,
please check that there is provision for ventilation at
the cabinet to ensure proper operation of the gas hob.
Do not store any flammable materials, sprays or
pressurized containers inside the stove cabinet.
The top panel of this cooker is made of tempered
glass/ceramic glass which is safer than normal glass
for this application.However,the following safety
precautions for using gas hob with glass top panel
should also be noted in order to prevent the glass top
panel from beraking:
1. Clean the burner assembly frequently to maintain
a clear gas passage on the flame distributor. Clean
and tidy up the flame distridistributor. Clean and tidy
up the flame distriburner assembly cooled down.
2. Turn off the gas appliance immediately ifabnormal
noise propagates from the gas appliance and contact
gas supply company or gas hob importer for inspection.
3. Do not use oversized utensils for cooking.
4. Do not impact the glass surface with hard objects
or place heavy objects on the glass surface.
The town gas model of this built-in hob has been
exempted from the mandatory requirement for the
installation of external gas governor.
I. 房間內通風
保持正常氣體燃燒及有關房間通風所需之空
氣量。空氣應自然流經房間內的固定窗戶或
通風口。通風系統須符合有關法例。
II.氣體接駁
注意
根據香港氣體安全規例，任何氣體裝置工
程，包括爐具和接駁喉管的安裝，必須由註
冊氣體裝置技工執行，而該技工已於相關的
氣體工程類別註冊及受聘於註冊氣體工程承
辦商。
使用認可印有機電工程署批准標記。例如：
機電工程署批准EMSD APPROVAL GTXXXX)的
氣體接駁喉管連接爐具，或使用機電工程署
接納的其他恰當方法。
當在灶櫃面安裝嵌入式氣體煮食爐時，灶櫃
應設有透氣設施，以確保煮食爐在使用時操
作正常。不應將易燃物料、噴霧及壓縮容器
放置在灶櫃內。
此煮食爐的面板是用強化陶瓷玻璃製造，較
一般玻璃安全。唯使用玻璃面板煮食爐時還
須注意以下事項，以避免玻璃面板爆裂：
1.經常清潔爐頭組件以保持火蓋焰孔暢通，
如滾瀉食物及汁液，應在爐頭組件冷卻後
儘快作出妥善清理。
2.如煮食爐出現不尋常聲音，應即停用並安
排氣體供應公司或爐具進口商檢查。
3.切勿使用過大的器皿煮食。
4.切勿以硬物撞擊或將重物放置於玻璃面板。
此煮食爐的煤氣嵌入式型號已豁免強制性需
要安裝外置氣體穩壓器的規定。
IV. Correct Position of Burner Rack &
Burner Cap
Make sure that the following parts are fitted properly
before use.
1. Burner Rack
Fit Burner Rack Legs into Drip Pan (Fig. 1).
III .
櫃面開孔尺寸
Cut-Out Dimensions
IV. 爐架及爐頭之正確位置
使用前請先確定以下配件已置於正確位置。
1.爐架
爐架正確地安放在爐碟上(圖1)。
型號
Model No.
A
B
R
GP12-1-LG, GP12-1-TG
265
463
0
GP12-2-LG, GP12-2-TG
674
364
30
GP12-2M-LG, GP12-2M-TG
463
342
0
GP12-3-LG, GP12-3-TG
798
463
0
櫃面
Counter Top
A
B
百葉窗
Venting Grille
R
