P.6
1. 使用前準備：
a. 將電炒鍋放在平穩的表面上。
b. 提起
“
開蓋手柄
”
打開上蓋(圖1)，將內鍋
取出。首先用手轉動鍋內攪拌器(圖2)，
確定能靈活轉動後，用水清洗乾淨，並
將內鍋外側用乾布擦洗乾淨，再放回機
內(圖3)。
2. 預熱：
a. 插入電源線，接通電源(圖4)。
b. 通電後電源指示燈開始閃爍，表示通電
正常。按
“
電源
”
鍵，此時顯示屏顯示
“
0000
”
，且電源指示燈由閃爍變為持續
亮起(圖5)，表示電炒鍋已進入預熱狀態。
c. 當機內發出信號音，顯示屏
“
0000
”
數字
閃爍時，表示炒菜機經已預熱完成，一般
預熱時間為2-2.5分鐘。
1. Prepare the appliance:
a. Place the Smart Stir Fryer on a flat and
stable surface .
b. Pull the “Lid Handle” to lift the lid (Fig. 1),
take out the inner pot. Ensure the stirrer
can move smoothly by manually stirring
them (Fig. 2), clean with water. Wipe the
outer side of the inner pot clean with dry
cloth and put it back in the unit (Fig. 3).
2. Preheat:
a. Connect power cord (Fig. 4).
b. The power indicator would start flashing when
power is connected properly. Press “ Power”
button, the display will show “0000” and
power indicator will light up constantly (Fig. 5),
which indicates preheat is in progress.
c. When the beeper sounds and “0000” starts
flashing on the display screen, preheat is
finished. Preheat takes 2-2.5 min normally.
操作說明
Operating Instructions
Note:
- Tap the edge of the inner pot with both hands
to check and make sure it is fitted to the heating
plate tightly. If it is not fitted properly, check if
there is dirt stuck on the surface of the inner
pot or the heating plate. Clean up all dirt to
avoid heat transmission being affected.
- Place the inner pot handle at the position that
would fit well when the lid is put down to
ensure the unit can be sealed properly.
註：
- 可用雙手按內鍋邊緣輕輕晃動，以檢查
及確保內鍋已緊貼加熱盤。若有鬆動，
請查看內鍋底或加熱盤表面是否有雜物，
並將雜物清除，以免影響熱力傳導。
- 請將內鍋手柄放在與上蓋凹槽對應的
位置，以便關上上蓋時可密封。
POWER
電源
1
2
3
START
開始
TIME
時間
STIR-FRY
炒
PAN-FRY
煎/烤
STEAM
蒸
STEW
燉
POWER
電源
1
2
3
START
開始
TIME
時間
STIR-FRY
炒
PAN-FRY
煎/烤
STEAM
蒸
STEW
燉
POWER
電源
1
2
3
START
開始
TIME
時間
STIR-FRY
炒
PAN-FRY
煎/烤
STEAM
蒸
STEW
燉
圖
1 Fig.1
圖
4 Fig.4
圖
5 Fig.5
圖
2 Fig.2
圖
3 Fig.3
