background image

www.cutweltools.co.uk    Tel: 01924 869610  E: [email protected]

1

.32

 

1

.33

 

www.cutweltools.co.uk    Tel: 01924 869610  E: [email protected]

STD

STD

 Operating Instructions

 

Standard and StandardFLEX Series vices

STANDARD 

and

 StandardFLEX

 series vices can be aligned on the 

machine table horizontally or vertically mounted.

Accurate 

positioning

 and 

alignment

 within centesimal tolerances is made 

through 16 H7 longitudinal or crossway keys. 

It is also possible to align the vice through calibrated ground screws 

(Not for 1-2 types)

POSITIONING

ALIGNMENT BETWEEN THE CROSS KEYWAY AND 

THE FIXED JAW PLATE

Set the vice vertically ensuring that it is perfectly parallel to 

the table

 

A

 

in both sides. 

Then with an indicator check the parallelism of the

keyway and its alignment with the fixed jaw plate.

The clamping 

on the machine table can be made through screws from the central groove or through side clamps.

Ideal clamping is through side

 

clamps

 (

Art. 296

).

 

Two vices aligned through central cross keys or ground screws or side lateral reference points guarantee the same reference and alignment on the fixed jaw          

section with accuracy within 

0.02mm

.

VICE CLAMPING ON THE MACHINE

 

TABLE

Art. 297

 

*

Art. 297

 

*

Machine table with T-slots

*

 

Standard equipment includes 1 pair of positioning key nut Art. 297

Art. 83B

Art. 83B

Machine table grid type

35

0,6

5

20

25,6

 - 0

+ 0.02

PRECISION BLOCKS

A

INSTRUCTIONS FOR CORRECT WORK-PIECE CLAMPING

2-

 Position the movable jaw 

Art120 / 120A

 loosening the 2 set 

screws 

Art.410

 in order to allow the ground ball 

Art.361

 to lift 

and then move the 

Art.258

 blocking group to the proper position 

on the vice base leaving roughly 5 mm space with respect to the 

workpiece to clamp. (

Pic.2

)

1-

 

Ensure that the vice is properly positioned and clamped to the 

machine table and that the fixed jaw 

Art.120 / 120A

 is properly assembled.

 (

Pic.1

)

Pic. 1

Pictures refer to 

Art. 1 “STANDARD”

 vice

3-

 

Tighten the 2 set screws 

Art.410

 through the T-wrench 

Art.376

 and 

ensure that the positioning ball 

Art.361

 is properly positioned in a 

spherical recess. 

INSTRUCTIONS FOR PROPER USE

Art. 127

Art. 410
Art. 258

Art. 361

~ 5 mm

Art. 258

Pic. 2

Art. 381

Art. 361

Art. 376

~ 5 mm

Art. 291

Pic. 3

Be careful that the positioning ball is not pushed in the hole used for the vice 

clamping screws. It is also possible to use a proper insert 

Art. 291

 with spherical 

recess in order to prevent bad blocking of the ball. 

(

Pic. 3

Art. 120 / 120A

INSTRUCTIONS FOR PROPER USE

Hard tightening down of the vice to the machine 

table by this method is 

NOT recommended

 

as it can distort gap X and prevent the moving 

jaw from sliding

x

Art. 296

Art. 296

THIS IS THE CORRECT WAY

 

Operating Instructions

 

Standard and StandardFLEX Series vices

Gerardi Standard Series

Gerardi Standard Series

Отзывы: