Genie GS-2669 DC Скачать руководство пользователя страница 110

Страница: 110 / 178

November 2016

Service and Repair Manual

Fault Codes

Part No. 1272220GT

GS-2669 DC • GS-3369 DC • GS-4069 DC

Troubles hooting "H XXX" and " PXXX" Faults

Troubleshooting "HXXX" and "PXXX" Faults

The procedure below illustrates typical steps for diagnosing and fixing faults of type "HXXX" and "PXXX".

Diagnostic Chart

1 Check the faulted device for a short or open circuit.

Good



Replace faulted device.

Good



Check short or open circuit of the harness or
connector between Ground Controls and faulted device.

Good



Repair or replace harness an/or connector.

Good



Good

3 Check GCON Electronic Control Module (ECM).



Replace ECM.

Wiring Diagram

The wiring diagram shown below illustrates how fault type "HXXX" and "PXXX" devices are typically wired.
The signal of these types of devices originates at the Ground Controls and terminates at system ground.

GCON
Electronic Control Module
(ECM)

Signal Wire

Signal Side

Device

Return Side

Return Wire

In order to successfully troubleshoot "HXXX" or "PXXX" type faults, the entire faulted out circuit must be
investigated.

Содержание GS-2669 DC



















































































































































































Результаты поиска

Содержание GS-2669 DC

Отзывы:

Похожие инструкции для GS-2669 DC

Бренды по названию

Популярные бренды

Genie GS-2669 DC, Руководство по обслуживанию и ремонту

Результаты поиска

Содержание GS-2669 DC

Отзывы:

Похожие инструкции для GS-2669 DC

Бренды по названию

Популярные бренды