background image

Operator's Manual

Fourth Edition • Third Printing

Part No. 1000033

 GS-2032 • GS-2632

7

SAFETY RULES

Decal Legend

Genie product decals use symbols, color coding
and signal words to identify the following:

Safety alert symbol—used to alert
personnel to potential personal
injury hazards. Obey all safety
messages that follow this symbol
to avoid possible injury or death.

Red—used to indicate the
presence of an imminently
hazardous situation which, if not
avoided, will result in death or
serious injury.

Orange—used to indicate the
presence of a potentially
hazardous situation which, if not
avoided, could result in death or
serious injury.

Yellow with safety alert symbol—
used to indicate the presence of a
potentially hazardous situation
which, if not avoided, may cause
minor or moderate injury.

Yellow without safety alert
symbol—used to indicate the
presence of a potentially
hazardous situation which, if not
avoided, may result in property
damage.

Green—used to indicate operation
or maintenance information.

Bodily Injury Hazard

Do not operate the machine with a hydraulic oil or
air leak. An air leak or hydraulic leak can penetrate
and/or burn skin.

Improper contact with components under any
cover will cause serious injury. Only trained
maintenance personnel should access
compartments. Access by the operator is only
advised when performing a pre-operation
inspection. All compartments must remain closed
and secured during operation.

Содержание GS-2632






































Отзывы: