background image

Operator's Manual

Fourth Edition • Third Printing

Part No. 1000033

 GS-2032 • GS-2632

13

Pre-operation Inspection

Be sure that the operator's, safety and

responsibilities manuals are complete, legible
and in the storage container located on the
platform.

Be sure that all decals are legible and in place.

See Decals section.

Check for hydraulic oil leaks and proper oil

level. Add oil if needed. See Maintenance
section.

Check for battery fluid leaks and proper fluid

level. Add distilled water if needed. See
Maintenance section.

Check the following components or areas for
damage, improperly installed or missing parts and
unauthorized modifications:

Electrical components, wiring and electrical
cables

Hydraulic power unit, tank, hoses,
fittings, cylinders and manifolds

Battery pack and connections

Drive motors

Wear pads

Tires and wheels

Ground strap

Limit switches, alarms and horn

Nuts, bolts and other fasteners

Platform entry chain or gate

Beacon and alarms (if equipped)

Brake release components

Safety arm

Pothole guards

Platform extension

Scissor pins and retaining fasteners

Platform control joystick

Check entire machine for:

Cracks in welds or structural components

Dents or damage to machine

Excessive rust, corrosion or oxidation

Be sure that all structural and other critical

components are present and all associated
fasteners and pins are in place and properly
tightened.

Be sure side rails are installed and bolts are

fastened

Be sure that the chassis trays are closed and

latched and the batteries are properly
connected.

Note: If the platform must be raised to inspect the
machine, make sure the safety arm is in place.
See Operating Instructions section.

Содержание GS-2632






































Отзывы: