ⓒ
2020
LaON
Technology Co., Ltd. All rights reserved.
37
Note:
When executing pairs on the Beltpack, within 3 seconds of pressing the Beltpack PWR button, press and
hold the Set button together. Otherwise, the Beltpack power may be off.
Note:
All radio transmissions are temporarily interrupted during pairing and recovered when the pair is complete.
Note:
When each Beltpack is paired with the Base Station for the first time, each ID number of the Beltpack is
generated sequentially.
If pairing completed properly:
On the main menu of the Beltpack, appears an ID number label that is generated sequentially from 1 to 128.
Once the pairing has been successfully completed, the 'Pairing...' message will be changed to 'Pairing
Completed' within 20 seconds as shown in the figure. And the LED adjacent to the Talk key on the Beltpack
flashes green.
Repeat the paring processing for each Beltpack.
If pairing is failed:
If the message 'Pairing...' appears in the Beltpack menu, it will take up to 20 seconds for the message 'Pairing
Failed' to appear. If pairing fails, try again. If these processes still do not work, contact your dealer or
manufacturer for further support.
Pairing for replacement
If a new Beltpack is being paired to replace the Beltpack ('BP001'), turn off 'BP001' and pair to ID 'BP001' with
the new Beltpack.
Note:
If the same Beltpack ID is duplicated, a communication error may occur.
Reset Beltpack labels, GENIE group channels.
Reset Belt Label
Initialize all set labels on the wireless Beltpack.
Reset Belt Group
Initialize the GENIE group channel settings for the wireless
Beltpack
.
Note:
After resetting, the corresponding data stored at the Base Station will be stored as factory defaults.
Unless initialization is actually required, run the reset with due care. All edited data will be missing.
Allocating Group channels to Beltpack
This process is to assign single or multiple Group channels to each Beltpack.
Move to a Group channel number which you want to select by rotary control (#16). Single or multiple groups
within the five groups (1 2 3 4 5) can be saved by pressing rotary control (#10) on each Group channel number.
To reverse the saved groups, press rotary control (#10) on the group number to be reversed. In order to change
the Group channel for a Beltpack which is already paired, follow the same process. When you enter the edit
mode, the icon ( ) will be changed to ( ).
Note:
Any edited data require pair to the applicable Beltpacks for reflecting it.
Pairing with a Base Station
Once the Beltpack Label and Group channel is edited and the applicable Beltpack is ready, move to the paring
icon ( ).
Ready for Beltpack
Turn on the Beltpack by pressing PWR button for 2 seconds and confirm the Normal menu is appeared. If the
Beltpack is not paired with the Base Station, the LED adjacent to the Talk key flashes red.
Beltpack operation for pairing
For pairing to a Beltpack, press rotary control (#10) on the paring icon ( ) of the Base Station. Then pairing
icon will be shown as the icon ( ). At this point, on the Beltpack, press and hold the SET button immediately
after pressing the PWR button. With this operation, the Beltpack will also be in ‘pairing mode’ and the message
‘Pairing…’ will appears, then release both buttons.
If the paring is completed successfully, the paring icon, ( ) will be shown on the Base Station menu screen.
On the Beltpack menu screen, a completion message will appear as shown in the following figure. And will
shortly return to the Normal menu. If registration fails, the failed message appears.
Pairing …
BPK01 ID:001
Pairing Completed
Pairing …
Pair- ID:000
PairingFailed
Figure.: Pairing failed status
Figure. Pairing completed status