manualshive.com logo in svg

Genesis GEN3t, Руководство пользователя, Страница: 291 / 1124

Поделиться
Скачать
Genesis GEN3t Скачать руководство пользователя страница 291

12.4.2

Input connectors

The LEMO 2B316 connector pin

-

out is compatible with the Liberty data

acquisition system. The mating male connector is LEMO P/N
FGG2B316CLADxx, where xx is the desired cable collet size or a similar size.

12.4.3

Bridge completion

Each bridge amplifier channel contains a pair of fixed 10 kΩ resistors for half

-

bridge completion that can be switched in by software control. The user can
install two resistors on the removable bridge completion card for another value
and/or precision half

-

bridge completion. If so, a soldered jumper must be

removed for correct operation.

Additional pins on the LEMO connector provide a precision 350 Ω resistor, plus
an additional value for quarter

-

bridge completion that has been provided by a

user. The user

-

provided value is located on a removable bridge completion

card. The completion sockets are designed for Vishay Micro Measurements
S

-

Type resistors but can be used with other similar types. A diagram of the card

layout on one of the following page shows the location of each resistor.

12.4.4

Shunt calibration

Each bridge amplifier channel contains 100 KΩ and 20 KΩ, 0.1% fixed precision
resistors that can be switched in by software control. With a gage factor of 2.00,
this resistor simulates the following values of deflection for various bridge
configurations.

Table 12.6: Deflection for various bridge configurations

 

100 KΩ

20 KΩ

BRIDGE

1000 Ω

350 Ω

120 Ω

1000 Ω

350 Ω

120 Ω

mV/V

2.4888

0.873

0.299

12.20

4.337

1.495

μstr full
bridge

1244

437

150

6098

2169

748

μstr 

1

/

2

bridge

2488

873

300

12195

4337

1496

μstr 

1

/

4

bridge

4975

1747

600

24390

8674

2991

A convenient plug

-

in module is provided to install one additional user

-

supplied

shunt resistor on each channel. The diagram below shows the location of the
resistors completed by the user. A fourth calibration resistor can be connected
to the connector pins externally. Any of the four available shunt cal resistors
can be switched in by software control to provide multi

-

point calibration and

linearity verification.

GEN3t

I3995-3.1 en   HBM: public

291

Содержание GEN3t





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов