GeneralAire Elite Steam DS15, Руководство пользователя

Страница: 19 / 28

Elite Steam +03U221903 REV 2. 1
Display Description Action
Red
Alarm
Relay
Notes
- -
Remote on-off open
Unit disabled
Off Off
Check AB-AB jumper or pres. switch
EE
Internal memory error Unit disabled
On On Contact Tech. Support
E0
Control board configuration not valid
Unit disabled On On
E1
High current alarm Unit disabled On
Turn off, check connections, check cylinder
(no limescale bridges between electrodes,
no electrodes short-circuited)
E2
Low production, lo w supply water conductivity
e xcessive foam/limescale in the cylinder
Unit disabled
Press “reset” key for 1 seconds to reset.
On On
Check supply water conductivity (too l ow?),
replace the cylinder.
E3
Cylinder lifetime expired
(1200 hours)
Press “reset” key for 1 seconds to reset.
The warning will be displayed 50 hrs later
until the hour counter is reset and the
cylinder replaced.
Off Off Change c ylinder (not urgent)
E4
Fill alarm, unable or slow fill
(current does not increase within
timeout)
Press “reset” key for 1 seconds to reset,
otherwise the warning will be reset aut - o -
matically e ve ry 10 minutes until the supply
water is available again.
0n On Check water supply and fill valve;
check drain valve for leakage
E5
Drain alarm, unable to drain
(current does not decrease within timeout)
Press “reset” key for 1 seconds to reset
On On Check drain valve and drain connection
E6
Cylinder exhausted
(critical performance detected)
The warning is automatically reset if
CompactSteam can produce the demand,
Off Off
Change cylinder (urgen t)
E7
Foam detected
Press “reset/sel” key for 1 seconds to reset
Off Off
If it continues, do some cleaning cycles
(read
chap. “Star ting with a n ew cylinder”)
E8
High Controller Temperature
(2000 hours)
Reset the hour counter (read chapter
Resetting the hour counter”)
Off Off
Change the cylinder.
E9
(above 8 0°C / 176
°F )
The warning is automatically reset if the
temperature decreases below 8 0°C / 176 °F.
Off
Off Check the ambient temperature,
replace the controller.
Tab. 5.a
5.6 Alarms
In the e vent of an alarm, the red alarm L E D will flash, the alarm relay will close, and the alarm code will flash in the display.
Multiple alarms will flash in sequence, alternating with the main di splay . Pressing the sel button for 2 seconds will reset
the alarms, although still active alarms will continue to display.
. 5 Using the E2 Humidistat 5
Press to select OFF, MANUAL or AUTO mode (if outdoor sensor is connected) .
OFF mode: The humidifier is turned off.
Suggested Setting Outdoor Temperatures
AUTO mode:
The E2 will automatically raise the humidity as the outdoor temperature increases. This pro v ides the hi g hest
NOTE:
If the outdoor temperature sensor fails, flashes and the unit will default to MANUAL mode.
.
To toggle between indoor / outdoor temperature and indoor humidity: Press .
To change the temperature unit: Press °C / °F
.
To set the temperature / humidity offset in MANUAL or AUTO mode:
1. Simultaneously press and when v iewin g the temperature or humidity readin g .
2. Use or to chan g e the settin g (
-
3 to 3).
3. Press and simultaneously or wait 5 seconds to confirm and mo v e onto the next settin g .
Lo or Hi will flash on the display when:
MEASUREMENT LO HI
Indoor temp. Below 0
o
C
(32
Above
99
o
F(37
o
C)
Outdoor temp. Below -40
o
C
(-40
o
F)
Above 50
o
C
(122
o
F)
Humidity Below 10% Above 90%
• If power is lost, current settin
g s are retained.
WARNING
Do not allow excess humidification. Excess humidity can cause condensation and enable mold and mildew g rowth.
15%
20%
25%
30%
35%
40%
-20F
-10F
0 F
+10F
+20F
+30F
-29C
-23C
-18C
-12C
-7C
-1C
possible humidity. The E2 will automatically lower the humidity as temperatures drop. This minimizes the risk of condensation ON
on cold surfaces like windows. You can adjust the Auto Humidity Index Set Point from 0(low) to 10(high) by press i ng
or
The Humidity Index is based on the outdoor temperature and indoor humidity. The humidity will switch ON/OFF according
to the calculated auto humidity index set point. Lower index sett ings are for older homes with less insulation and vapor barrie rs.
Higher Index settings are for newer homes with complete vapo r barriers, triple pane windows, and high R value insulation.
If condensation occurs reduce Index setting by 2 points until co ndensation stops.
.
F)
o
Led
Cylinder lifetime expired
19
On
Contact Tech. Support
MANUAL mode:
The E2 will work to maintain the si ngl e humidity selected.
You can set your desired humidity l evel by pressing or . The humidi -
fier will turn ON or OFF according to your manual setting. (The humidifier
will operate when the measured rela tive humidity falls more than 2% below
the set point). Humidity will have to be lowered when weather is colder or if
condensation is suspected.