General Standards Corporation PCIe4-SIO8BX2 страница 32 Скачать руководство пользователя | Manualshive

Страница: 32 / 42

background image

27

Rev NR

4.1.2 Local Configuration Registers

The Local Configuration registers give information on the Local side implementation. These include the required
memory size. The SIO8BX2 memory size is initialized to 4k bytes. All other Local Registers initialize to the default
values described in the PCI9056 Manual.

4.1.3 Runtime Registers

The Runtime registers consist of mailbox registers, doorbell registers, and a general-purpose control register. The
mailbox and doorbell registers are not used and serve no purpose on the SIO8BX2. All other Runtime Registers
initialize to the default values described in the PCI9056 Manual.

4.1.4 DMA Registers

The Local DMA registers are used to setup the DMA transfers to and from the on-board FIFOs.  DMA is
supported only to the four FIFO locations.  The SIO8BX2 supports both Demand (DREQ# controlled) and Non-
Demand mode DMA.  Both Channel 0 and Channel 1 DMA are supported.

4.1.4.1 DMA Channel Mode Register: (PCI 0x80 / 0x94)

The DMA Channel Mode register must be setup to match the hardware implementation.

Bit

Description

Value

Notes

D1:0

Local Bus Width

11 = 32 bit
00 = 8 bit

Although the serial FIFOs only contain 8 bits of
data, the register access is still a 32bit access. It is
possible to “pack” the data by setting the Local
Bus Width to 8, but this is only guaranteed to
work with Non-Demand Mode DMA

D5:2

Internal Wait States

0000 = Unused

D6

Ready Input Enable

1 = Enabled

D7

Bterm# Input Enabled

0 = Unused

D8

Local Burst Enable

1 = Supported

Bursting allows fast back-to-back accesses to the
FIFOs to speed throughput

D9

Chaining Enable (Scatter
Gather DMA)

X

DMA source addr, destination addr, and byte
count are loaded from memory in PCI Space.

D10

Done Interrupt Enable

X

DMA Done Interrupt

D11

Local Addressing Mode

1 = No Increment

DMA to/from FIFOs only

D12

Demand Mode Enable

X

Demand Mode DMA is supported for FIFO
accesses on the SIO4BXR.
(See Section 3.3)

D13

Write & Invalidate Mode

X

D14

DMA EOT Enable

0 = Unused

D15

DMA Stop Data Transfer
Enable

0 = BLAST
terminates DMA

D16

DMA Clear Count Mode

0 = Unused

D17

DMA Channel Interrupt
Select

X

D31:18

Reserved

0

«
...
30
31
32
33
34
...
»

Содержание PCIe4-SIO8BX2











































Отзывы:

Нет отзывов

Похожие инструкции для PCIe4-SIO8BX2

Бренд: Q-See Страницы: 97

Бренд: ELSA Страницы: 42

Бренд: Narvitech Страницы: 16

Бренд: Gigabyte Страницы: 38

Бренд: Aaeon Страницы: 55

ImageMate SDDR-88

Бренд: SanDisk Страницы: 63

Бренд: Anker Страницы: 14

Бренд: Hama Страницы: 24

Бренд: Nokia Страницы: 16

Бренд: Octagon Страницы: 25

Бренд: ATEN Страницы: 13

Бренд: EMS Imaging Страницы: 29

Бренд: Diablotek Страницы: 1

Бренд: MOTU Страницы: 270

USB 2.0 56IN1 CARD READER

Бренд: Vivanco Страницы: 2

Бренд: Vivanco Страницы: 2

Бренд: Vivanco Страницы: 2

Бренд: Certgate Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды