General Standards Corporation PCIe4-SIO8BX2 страница 17 Скачать руководство пользователя

Страница: 17 / 42

Rev NR

D28

DCE/DTE Mode
When DCE/DTE Mode is enabled (Bit D31=1), this bit set the mode to DCE (1) or DTE (0).
DCE/DTE mode changes the direction of the signals at the IO Connector.

D27:24

Transceiver Protocol Mode

D27

D26

D25

D24

Transceiver Mode

RS-422 / RS-485

RESERVED

RS-232

RESERVED

D23

Internal

Loopback Mode

When DCE/DTE Mode is enabled (Bit D31=1), this bit will automatically loopback the TxC/RxC,
TxD/RxD, and RTS/CTS signals internal to the board.

D22

Reserved

D21:19

Cable TxD Output Control

Allows TxD output to be used as a general purpose output.

D21

D20

D19

TxD Source

USC_TxD

Output ‘0’

Output ‘1’

Differential Biphase Mark

Differential Biphase Space

Level

Differential Biphase Level

D18:17

Cable TxAuxC Output Control

Defines the Clock Source for the TxAuxC signal to the IO connector.

D18

D17

TxAuxC Source

Tristate

On-board Programmable Clock

Output ‘0’

Output ‘1’

D16:15

Cable DCD Output Source

D16

D15

Output Source

Notes

USC_DCD Output

USC_DCD field (D12:D11) must equal ‘11’

RTS Output

Rx FIFO Almost Full

‘0’

Drive low

‘1’

Drive Hi

Содержание PCIe4-SIO8BX2











































Результаты поиска

Содержание PCIe4-SIO8BX2

Отзывы:

Похожие инструкции для PCIe4-SIO8BX2

Бренды по названию

Популярные бренды

General Standards Corporation PCIe4-SIO8BX2, Руководство пользователя

Результаты поиска

Содержание PCIe4-SIO8BX2

Отзывы:

Похожие инструкции для PCIe4-SIO8BX2

Бренды по названию

Популярные бренды