General Monitors S4000C Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 54

background image

S4000C

4.0 Operation

4.1 Start-Up Checklist

Prior to starting the system, verify the following:

1. Inhibit any external devices, such as Trip Amplifiers, PLC’s, or DCS systems.

2. Verify that the optional settings are set for the desired configuration.

3. Verify that the unit is properly mounted. Ensure the conduit/cable gland entries are

pointed downward.

4. Verify that the signal wiring is correct.

5. Verify that the power supply is connected properly. The Model S4000C is powered by

+24VDC (20 to 36 VDC voltage range). The detector will output a low voltage (F6) fault
at 18.5 VDC or below.

6. Make sure the lid is securely installed or the area has been declassified.

4.2 Start-Up

Before applying power to the system for the first time, all wiring connections should be checked
for correctness and the housing cover replaced. Upon first power-up the sensor may take up to
fifteen minutes to stabilize.

At the initial application of power, the unit will test all of the LED segments by displaying “

88.8

”.

The software revision letter will then be displayed for a few seconds. The unit will then enter a
fifty second Start-Up mode. During this period, the display will read “

SU

”. The unit will then

enter Operational Mode, and the current gas concentration at the sensor will be displayed. For
details of Calibrating and Gas Checking the unit, see Sections 4.5 and 4.6.

4.3 Relay Reset

If the Warn and Alarm relays are configured as latching, they must be manually reset, after an
alarm occurs. This can be accomplished by three different methods:

1. The relays can be reset via the MODBUS Interface (Section 8.8.16).

2. The relays can be reset via the magnetic switch using a magnet. Place the magnet

over the GM Logo on the cover of the unit. After three seconds, the display will show
“rSt”. Remove the magnet at this time and the relays will be reset (Figure 10).

13

«
...
21
22
23
24
25
...
»

Содержание S4000C























































Отзывы:

Нет отзывов

Похожие инструкции для S4000C

Бренд: GE Страницы: 2

Бренд: Calumet Страницы: 4

Бренд: Manfrotto Страницы: 2

Бренд: Garmin Страницы: 26

Бренд: Garmin Страницы: 33

Бренд: Garmin Страницы: 167

Бренд: Tait Страницы: 10

Powersaver Dual Flexi

Бренд: Sangamo Страницы: 2

Бренд: Targus Страницы: 4

Бренд: Targus Страницы: 2

Бренд: Tarot Страницы: 5

Бренд: UniFlow Страницы: 42

WrapAround Windjammer

Бренд: Bestop Страницы: 7

Ceiling Trim Kit for Home2 Series

Бренд: Elite Screens Страницы: 8

Бренд: R&G Страницы: 4

Бренд: Waeco Страницы: 168

Бренд: Olympus Страницы: 268

Бренд: ZF Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды