General DataComm SC-ADT 16 Por Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 106

background image

SC-ADT Configuration

Port Configuration

076R172-000

SpectraComm ADT

3-21

Issue 6

Installation and Operation Manual

Bypass Modem Port Configuration

The SC-ADT front panel Port1 and Port2 can be configured as bypass modem ports (

m0

and

m1

).

This allows the SC-ADT to provide an IP address to an attached customer-supplied IP device and
forward data to that device (no modem required).

For online help in configuring bypass modem modes, type:

configure modem bypass ?

Figure 3-6

Modem Bypass Help Displays

Bypass Modem Configuration Procedure

1. Check that the customer-supplied IP device is properly connected to Port1 or Port 2.

(Port1 is

m0

; Port 2 is

m1

). Refer to Chapter 2 under

Modem Connections

as needed.

2. Check that any port intended for Bypass modem use is not currently in use as a Term or Tranport port.

3. Configure the modem interface for Bypass Mode as follows:

configure modem use bypass modem

[0 or 1]

4. Set the bypass rate for both modem interfaces (from 2400 to 115200):

configure modem bypass rate

[9600]

Note

If Port1 and Port2 are both configured for modem use, the ports will be locked to the same DTE rate as
configured by the user. Be aware that when one modem port is configured for modem bypass and the other
for an internal/external modem, the DTE rate for both ports will be locked to the configured bypass rate.

5. Set the bypass disconnect on loss of DTR or RTS from DTE:

configure modem bypass disconnect

[rts]

modem

[0 or 1]

6. Configure each modem interface by typing:

configure interfaces ip-address modem

[0 or 1]

[###.###.###.###] [###.###.###.###]

For example:

configure interfaces ip-address modem0 192.168.11.20 255.255.255.0

7. Enter a description for each modem interface by typing:

configure interfaces description modem

[0 or 1]

[your_description]

8. Enable the modem interfaces by typing:

configure interfaces enable modem

[0 or 1]

9. Enable access to modem services by typing:

services access enable modem

[0 or 1]

ADT-16% configure modem bypass ?

___________Help for "configure modem bypass "______________________
rate Set bypass rate. (Affects both modems); requires 1 parameter(s)
disconnect Set disconnect on signal loss from DTE
udp-port Set bypass udp port; requires 2 parameter(s)
gateway Set IP address of bypass gateway; requires 2 parameter(s)

«
...
57
58
59
60
61
...
»

Содержание SC-ADT 16 Por











































































































Отзывы:

Нет отзывов

Похожие инструкции для SC-ADT 16 Por

Бренд: D-Link Страницы: 11

Бренд: D-Link Страницы: 8

AirPlus DWL-810

Бренд: D-Link Страницы: 8

Бренд: D-Link Страницы: 12

Бренд: D-Link Страницы: 84

Бренд: D-Link Страницы: 12

Бренд: ZETR Страницы: 2

Бренд: CallDirect Страницы: 33

Бренд: IBM Страницы: 4

Бренд: Observint Страницы: 117

Бренд: CSS Страницы: 2

Бренд: C-Data Страницы: 26

Бренд: XMOS Страницы: 6

PCI-6110E/6111E

Бренд: National Instruments Страницы: 113

Aquaduct 360 XT

Бренд: Aqua Computer Страницы: 28

ELC-LTTR240-TBP

Бренд: ENERMAX Страницы: 16

Бренд: A2B Electronics Страницы: 24

Бренд: ZALMAN Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды