manualshive.com logo in svg

Generac Power Systems MGG155, Руководство по эксплуатации

Поделиться
Скачать
Generac Power Systems MGG155 Скачать руководство пользователя страница 7

35319 C

MGG155/210 Operating Manual

1

Section 1 - Safety

SAFETY NOTES

This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety 
messages that follow this symbol to avoid possible injury or death. 

This manual contains DANGERS, WARNINGS, CAUTIONS, NOTICES and NOTES which must be 
followed to prevent the possibility of improper service, damage to the equipment, personal injury or death. 
The following formatting options will apply when calling the readers attention to the DANGERS, WARN-
INGS, CAUTIONS, NOTICES and NOTES.

DANGER

INDICATES A HAZARDOUS SITUATION WHICH, IF NOT AVOIDED, WILL RESULT IN 

DEATH OR SERIOUS INJURY. (000001)

WARNING

Indicates a hazardous situation which, if not avoided, could result in death or serious 

injury. (000002)

CAUTION

Indicates a hazardous situation which, if not avoided, could result in minor or moderate 

injury. (000003)

Indicates a hazardous situation which, if not avoided, could result in property or equipment 

damage.

Note: 

Notes contain additional information important to a procedure and will be found within the regular text body 

of this manual.

OPERATING SAFETY

Before using the unit, be sure you read and understand all of the instructions. This equipment was 
designed for specific applications; 

DO NOT

 modify or use this equipment for any application other than 

which it was designed for. Equipment operated improperly or by untrained personnel can be dangerous.   
Read the operating instructions and familiarize yourself with the location and proper use of all instruments 
and controls. Inexperienced operators should receive instruction from someone familiar with the equipment 
before being allowed to operate or set up the unit. The following points should be practiced at all times:

•

The area immediately surrounding the unit should be dry, clean, and free of debris.

•

Position and operate the unit on a firm, level surface.

•

DO NOT

 start a unit in need of repair.

•

If the unit is equipped with a frame grounding stud, follow any local, state, and National Electrical 
Code (NEC) guidelines when connecting.

•

DO NOT

 operate the unit on a combustible surface.

•

DO NOT

 operate a unit while tired, distracted, or under the influence of drugs or alcohol.

•

Keep all body parts, clothing and other loose items away from moving parts.

•

All fuel types are potentially FLAMMABLE and/or EXPLOSIVE and should be handled with care. 
Comply with all laws regulating the storage and handling of fuels. Inspect the unit’s fuel system 
frequently and correct any leaks immediately. Fuel supply lines must be properly installed, purged, 
and leak tested according to applicable fuel-gas codes before placing the equipment into service.

Discount-Equipment.com

Содержание MGG155




































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды