manualshive.com logo in svg

Generac Power Systems MGG155, Руководство по эксплуатации

Поделиться
Скачать
Generac Power Systems MGG155 Скачать руководство пользователя страница 44

Maintenance

35319 C

MGG155/210 Operating Manual

39

JACK MAINTENANCE

The following procedures should be performed annually. 

Side-Wind Models

•

The internal gearing and bushings of the jack must be kept lubricated. Apply a small amount of automotive 
grease to the internal gearing by removing the jack cover, or if equipped, use a needle nose applicator or 
standard grease gun on the lubrication point found on the side of the jack near the crank. Rotate the jack 
handle to distribute the grease evenly. 

•

A lightweight oil must be applied to the handle unit at both sides of the tube. 

•

If equipped, the axle bolt and nut assembly of the caster wheel must also be lubricated with the same 
lightweight oil.

Top-Wind Models

•

Apply a lightweight oil to the screw stem.

Figure 18 - Lubrication Points

TRAILER WHEEL BEARINGS

The trailer axles are

 

equipped with a grease fitting to allow lubrication of the wheel bearings without the need to 

disassemble the axle hub. To lubricate the axle bearings, remove the small rubber plug on the grease cap, attach a 
standard grease gun fitting to the grease fitting and pump grease into the fitting until new grease is visible around 
the nozzle of the grease gun. Use only a high quality grease made specifically for lubrication of wheel bearings. Wipe 
any excess grease from the hub with a clean cloth and replace the rubber plug when finished. The minimum 
recommended lubrication is every 12 months or 12,000 miles (19,312 km). More frequent lubrication may be required 
under extremely dusty or damp operating conditions.

Oil

Grease

Grease

Grease

Oil

Oil

Oil

Oil

00243

Discount-Equipment.com

Содержание MGG155




































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды