manualshive.com logo in svg

Generac Power Systems MAGNUM MLT6SKDS, Руководство пользователя

Поделиться
Скачать
Generac Power Systems MAGNUM MLT6SKDS Скачать руководство пользователя страница 9

Introduction and Safety

Owner’s Manual for MLT6SMDS - MLT6SKDS Light Tower

5

Raising and Lowering the Mast

•

Keep  area  around  the  unit  clear  of  people  while
raising and lowering the mast.

•

ALWAYS 

lower the mast when not in use.

•

The  tower  extends  up  to  23  ft  (7  m).  Verify  area
above  trailer  is  open  and  clear  of  overhead  wires
and obstructions.

•

If for any reason any part of the mast hangs up or
winch  cable  develops  slack  while  raising  or
lowering  tower,  stop  immediately  and  contact  a
GMP ASD.

•

NEVER 

remove safety pin or pull mast locking pin

while tower is up.

Service Safety

This  unit  uses  high  voltage  circuits  capable  of  causing
serious  injury  or  death.  Only  a  qualified  and  licensed
electrician  should  troubleshoot  or  repair  problems
occurring in this equipment.

•

Before  servicing  the  unit,  verify  the  control  power
switch  and  circuit  breakers  are  OFF  (O),  and  the
negative  (-)  terminal  on  the  battery  is  discon-
nected. 

DO NOT

 perform even routine service (oil/

filter  changes,  cleaning,  etc.)  unless  all  electrical
components are shut down.

•

ALWAYS 

use extreme caution when servicing this

unit in  damp  conditions. Do  not  service  the unit  if
skin or clothing is wet. Do not allow water to collect
around the base of the unit.

•

DO NOT

 wash the unit with high pressure hoses,

power  washers,  or  steam  cleaners.  Water  may
collect  in  the  unit,  causing  damage  to  electrical
parts. 

•

Replace  all  missing  and  hard  to  read  decals.
Decals  provide  important  operating  instructions
and warn of dangers and hazards.

•

Wear  heavy  leather  gloves  when  handling  winch
cables. Never let cables slip through bare hands.

•

Only  use  mild  soap  and  water  to  clean  the  lens
covers.  Other  chemicals  may  damage  the  lens
covers.

WARNING

       Electrocution. Do not set up or operate 
       this unit if severe weather is expected.
Lightning strikes can kill or cause severe injury
even if you are not touching the unit.

(000296)

WARNING

(000297)

> 60 mph

> 60 mph

Do not set up the unit if high winds 
are expected. High winds can cause the 
unit to tip or fall, causing severe injury 
or machine damage.

(000279)

Personal injury or equipment damage. Do not raise 
or lower the mast while the unit is operating. 
Doing so can break the lenses and cause the 
lamps to shatter.

WARNING

WARNING

Personal Injury. Stop immediately if the mast hangs 
up or the winch cable develops slack. Excess slack 
could cause the mast to collapse, resulting in personal 
injury or equipment damage.

(000265)

WARNING

(000266)

Tipping hazard. Extend the outriggers and level the unit 
before raising the mast. Keep the outriggers extended while 
the mast is up. Failure to do so could cause the unit to tip 
and fall and could result in death or serious injury. 

(000148a)

WARNING

Accidental start-up. Disconnect negative battery 
terminal before servicing to prevent accidental engine 
rotation. Failure to do so could result in death or 
serious injury.

Содержание MAGNUM MLT6SKDS





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды