manualshive.com logo in svg

Generac Mobile G4-ECO, Руководство пользователя

Поделиться
Скачать
Generac Mobile G4-ECO Скачать руководство пользователя страница 29

Owner’s Manual for G4-ECO Light Tower

25

Operation

Start Procedure

1. Turn Utility/Off/Generator selector on control panel 

to the desired power source. See 

Control Panel

for location.

•

Generator powers the light tower using the unit 
generator/engine.

•

Utility powers the light tower using the power 
source connected to the control panel power inlet.
See 

Operation Configuration

 for more

 

information.

NOTE: 

When using utility power, the mains utility voltage 

and frequency are displayed on the controller screen, 
and all engine icons, inputs, alarms, and procedures are 
disabled.

2. Turn ON main circuit breaker and mast light 

breakers. 

3. Use the controller Manual/Auto button to select the

 

desired mode.

•

Manual mode is the system default. In Manual 
mode, the user manually turns the light tower ON

 

and OFF. When Manual mode is selected the

 

Manual mode icon will appear on the controller 

screen: 

.

•

Automatic mode automates light tower control 
based on presets. The Light Sensor preset turns 
the unit ON/OFF when ambient light reaches a 
threshold. The Timer preset turns the unit ON/OFF

 

based at a user-defined time. When Automatic 
mode is selected, the default Manual mode icon 

 will be replaced by Automatic mode icons:  

for Light sensor, and 

 for Timer. See 

Setting

 

Light Sensor

 and 

Setting the Timer

 for more 

information. 

4. Press the controller Start/Stop button to start the

 

engine.

NOTE: 

During startup, the unit will perform a series of 

routine system checks before the light tower can be

 

used. The controller indicates the light tower is ready for 

use when the engine icon 

 

stops blinking and turns 

solid. 

5. Use the controller Lamps 1-4 On/Off buttons to 

switch the desired lamps ON. 

NOTE: 

The lamps do not turn ON simultaneously. There 

is a delay between lights. The status LED above the lamp 
switch will blink during this delay, and stop blinking when 
the lamp switches ON. 

Lowering the Mast

WARNING

Personal Injury. Stop immediately if the mast hangs 
up or the winch cable develops slack. Excess slack 
could cause the mast to collapse, resulting in personal 
injury or equipment damage.

(000265)

1. Shut off lights. 
2. Use winch handle to lower the mast to its lowest 

position. Verify the electrical cord does not get 
caught in, or pinched by, the mast while it is being 
lowered.

IMPORTANT NOTE: 

Contract a Generac Mobil Product 

Authorized Dealer immediately if the mast hangs up or 
the winch cable develops slack.

Customer Convenience 

Receptacles

See 

Figure 3-9

. The unit is equipped with convenience

 

outlets for powering accessories or tools. Power is 
supplied to the outlets any time the engine is running. 
Each outlet has an individual circuit breaker, located on 
the control panel. 
The circuit breakers are labeled with the corresponding

 

voltage for the receptacle they protect. The standard 
receptacle panel is equipped with the following 
receptacles:

•

One 120/240VAC-20A L14-20R (A) 

•

Two 120VAC-15A GFCI receptacle (5-15R) (B)

With all of the lights OFF, full generator power output is 
available to the receptacles.

NOTE: 

See 

Table 3-9

 for recommended cable size and

 

length.

A

B

Figure 3-9. Customer Convenience Receptacles

Содержание G4-ECO













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды