To carry out the operation successfully, make sure the required electrical connections
(bonnet push-button and positive under key) have been made.
!
All device previously programmed in the memory can be erased; to clear memory proceed as follows:
With system disarmed, open and keep opened the vehicle bonnet
!
.
!
!
!
Turn ignition key “ON-OFF”-“ON-OFF”-“ON-OFF”-“ON”; after the fourth rotation, leave it “ON”.
.
Close the bonnet and k
.
To confirm it has entered in the delete mode, the system gives two acoustic signals (one high and
one low-pitched), the turn indicators flash once and the LED turns ON
eep it closed (approx. 8 sec.) until the devices are completely deleted
The following operations must be carried out within four seconds otherwise the
procedure is invalidated.
If the bonnet is opened before 8 seconds, the devices will not be
deleted.
!
!
!
!
”.
.
The status LED turns OFF when the devices have been deleted; turn ignition key “OFF
The end of the procedure is indicated by one long low-pitched acoustic signal
15.0 - DELETION OF PROGRAMMED DEVICES
To carry out the operation successfully, make sure the required electrical connections
(bonnet push-button and positive under key) are complete.
!
To activate the procedure proceed as follows:
With system disarmed, open the bonnet and leave it open
!
.
!
!
Turn ignition key “ON-OFF”-“ON-OFF”-“ON-OFF”-“ON”; at the fourth rotation, leave it “ON”.
.
To confirm it has entered in the self-learning mode, the system gives two acoustic signals (one high
and one low-pitched), the turn indicators flash once and the LED turns ON
The following operations must be carried out within four seconds otherwise the
procedure is invalidated.
Do not close the bonnet otherwise all previously programmed devices are erased as
described in the next paragraph.
Storing memory is for 55 devices; saving to memory the 56th. device has as a result the
deletion of the first device installed in the location one of the alarm memory.
!
!
!
!
!
R
he end of the procedure is indicated by
.
Insert the electronic key into the receptacle; each time a device is learned a high-pitched signal
sounds and the status LED turns OFF briefly.
epeat this procedure to store other devices.
Turn ignition key “OFF”; t
a low-pitched signal sounds, the
turn indicators flash once and the status LED turns OFF
!
14.0 - ADDITION OF NEW DEVICES
INSTALLER MANUAL - PAGE 15
PAGE 14 - INSTALLER MANUAL
To reset the system proceed as follows:
Switch-off
power supply
hort-circuit the RED and BLACK wires of the 2-way
connector
Switch the
on; once the alarm system is powered, 4 acoustic signals will sound and the turn
indicators will flash 4 times
Remove the previously created short-circuit; the status LED lights up steady.
reset is confirmed by an aucoustic signal and the wailing of the siren for
approx. 3 seconds
the LED will turns off. There are no acoustic signals
!
!
!
!
!
!
system
.
S
LED
.
system
.
Turn ignition key “ON”;
.
Turn ignition key “OFF”;
.
By activating the following procedure, the system returns to the Factory default setting.
This procedure must therefore only be used in case of need, before programming the
system or auto-learning the turn indicators flashes.
!
16.0 - U
16.1 - CONNECTIONS AND POSITIONING
16.2 - SENSOR ADJUSTMENT
I
.
:
.
LTRASONIC VOLUMETRIC PROTECTION
nsert the WHITE connector in the “W” marked socket and the RED connector in the “R” marked
socket (see figure below).
Install the transducers of the ultrasonic sensors on the top part of the windscreen internal pillars, away
from the air vents and orient them towards the center of the rear window
To check sensitivity level proceed as follows
With the alarm system disarmed, roll down the front window about 20 cm.
Adjust trimmer at a medium setting.
Close all doors, bonnet and boot and arm the system.
During the system inhibit arming time introduce an object in the cabin through the window and
move it around; the status LED will turn off to signal a presence.
If sensitity lelvel is too high or too low, readjust the trimmer and repeat the above procedure
!
!
!
!
!
17.0 - SYSTEM RESET
ULTRASONIC
CELLS
CONNECTIONS
SENSITIVITY
ADJUSTMENT