Gemalto Cinterion PLS62T-W USB Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 91

Gemalto Cinterion PLS62T-W USB Скачать руководство пользователя страница 59

Cinterion

®

Java Terminal Hardware Interface Description

6.2 Restrictions

61



PLS62T-W_HID_v01

2018-06-20

Confidential / Prelimenary

Page 59 of 91

6.2

Restrictions

Later enhancements and modifications beyond the certified configuration require extra approv-
als. Each supplementary approval process includes submittal of the technical documentation
as well as testing of the changes made.
•

No further approvals are required for customer applications that comply with the approved
Java Terminal configuration.

•

Extra approval must be obtained for applications using other accessories than those
included in the approved Java Terminal configuration (power supply, MMI implementation
supported by AT commands).

6.3

CE Conformity

The Java Terminal meet the requirements of the EU directives listed below:

•

RED Directive 2014/53/EU

The Java Terminal are marked with the CE conformity mark (without a notified body number):

6.4

EMC

The Java Terminal comply with the equipment requirements specified in EN 301489-1, and
-52 are covered by the RED Directive. For details see

.

Conformity mark

«
...
57
58
59
60
61
...
»

Содержание Cinterion PLS62T-W USB




























































































Отзывы:

Нет отзывов