Gemalto Cinterion ENS22-E Скачать руководство пользователя страница 92

Страница: 92 / 189

Cinterion

ENS22-E AT Command Set

7. Internet Service Commands



ENS22-E_ATC_V01.000

19/02/11

Page 92 of 189

Internet Service Commands

Cinterion

ENS22-E has an embedded TCP/IP stack that is driven by AT commands and enables the host

application to easily access the Internet. The advantage of this solution is that it eliminates the need for the

application manu-facturer to implement own TCP/IP, thus minimizing cost and time to integrate Internet

connectivity into a new or existing host application. This chapter is a reference guide to all the AT commands

and responses defined for use with the TCP/IP stack.

The embedded TCP/IP stack provides the following services:

Socket Services:

- UDP Client in Non-Transparent or Transparent Mode
- Non-Transparent UDP Endpoint

Please note that a total number of 5 sockets is available for usage.

Step-by-step overview of how to configure and use TCP/IP communications with

Cinterion

ENS22-E:

• Select URC mode or polling mode as described below.
• First of all, create a GPRS connection profile with

AT^SICS

. The connection profile is a set of basic param-

eters which determines the type of connection to use for an Internet service. The connection type is also

referred to as bearer. Up to 5 connection profiles can be defined, each identified by the

• Secondly, use

AT^SISS

to create a service profile based on one of the connection profiles. Up to 5 service

profiles can be defined, each identified by the

. The service profile specifies the type of

Internet service to use, e.g., Socket. To assign a connection profile to a service profile, the

AT^SICS

must be entered as "conId" value of the

AT^SISS

parameter

This offers great flexibility to combine connection profiles and service profiles.

• Once the connection profile and the service profile are created, an Internet session can be opened by entering

the

AT^SISO

write command and the desired

A URC indicates how to proceed. The "

^SISW

" URC means that data can be sent. The "

^SISR

" URC means

that received data are available for reading. If an error occurs the "

^SIS

" URC is delivered instead.

• The next steps differ depending on the service type and the transfer mode (Non-Transparent or Transparent).
• Once a service is opened, the

AT^SISI

command shall be used to monitor the progress of the session. The

command reports the service state of the used service profile and indicates the number of bytes received, the

number of bytes sent.

• If an error occurs during a session you can enter the

AT^SISE

command and the

to iden-

tify the reason. This is especially important in polling mode.

• The

AT^SICI

command can be used any time to query the current status of one or all connection profile(s).

• Finally, to close an opened service, enter the

AT^SISC

write command and the

• All profile settings of

AT^SISS

and

AT^SICS

are volatile. To store the settings to non-volatile memory and

load the stored profiles

AT^SIPS

can be used.

Transparent Mode or Non-Transparent Mode:

•

Transparent Mode

is stream-oriented, i.e. a single data stream can be sent, and another single data stream

can be received. Packetizing of data is done automatically by the embedded TCP/IP stack.

Transparent Mode is activated with

AT^SIST

and then indicated by the "CONNECT" result code. The mode

eliminates the need for

AT^SISW

and

AT^SISR

read and write sequences.

•

Non-Transparent Mode

is packet oriented, i.e. data is transferred in separate packets. Maximum packet size

is 1358 bytes for UDP. To read and write data

AT^SISW

an d

AT^SISR

sequences shall be used.

To send or receive more than 1358 bytes, the read or write action shall be repeated until the data transfer has

completed. Each read or write action requires that the command response (of

AT^SISR

AT^SISW

) con-

firms that the service is ready to send or receive data. The read/write cycles can be controlled by URCs or

polling. For details see below section "URC mode and polling mode".

• UDP Endpoint employ Non-Transparent Mode.

UDP client can employ both modes, and may even mix both modes in the same connection.

Содержание Cinterion ENS22-E






























































































































































































Результаты поиска

Содержание Cinterion ENS22-E

Отзывы:

Бренды по названию

Популярные бренды

Gemalto Cinterion ENS22-E, Набор команд AT

Результаты поиска

Содержание Cinterion ENS22-E

Отзывы:

Бренды по названию

Популярные бренды