Gemalto Cinterion EHS6 страница 465 Скачать руководство пользователя

Страница: 465 / 513

Cinterion

EHS6 AT Command Set



19.7 AT^SSPI



EHS6_ATC_V03.001

15/12/3

Confidential / Released

Page 465 of 513

19.7.2

Transmitting Data over AT Interface

This section provides information on the protocol used for data transmission to or from I²C /SPI devices and

explains the data mode. It is assumed that you are familiar with the I²C specification.



Throughout this section the following document conventions are used to mark the direction of send and receive:



Transfer Message: AT

→

I²C or SPI device driver



Response Message: AT

←

I²C or SPI device driver



Channel Open / Close:



To change from command mode to data mode use the

AT^SSPI

write command. To close down the channel

and return to command mode send the ASCII code # (0x23).



ASCII Protocol for I²C or SPI communication over AT interface:



The protocol allows using a Terminal program for the communication between the module and the I²C slave

device/SPI device. To visualize transferred characters and response data it is recommended to run the Terminal

program in chat mode or to switch on local echo.



For transfer and response, special characters are defined, such as Start and Stop to mark a single message and

Close to disconnect the data channel. All valid special characters are listed below:

Table 19.2:

Special characters for ASCII coding

Direction



AT - Driver

Function in protocol

Special



character

Hex value

Description

→

Start Transfer Message

0x3C

Special character sent to the I²C/SPI

driver to start sending.

→

Stop Transfer Message

0x3E

Special character sent to the I²C/SPI

driver to stop sending.

→

Channel Close

0x23

For signalling.



Channel Close can be sent any time inside

or outside a transmit or receive message.

Causes the transfer to be aborted and

takes the ME back to AT command mode.

←

Start Response Message {

0x7B

Special character sent to the I²C/SPI

driver to mark the beginning of a Response

Message.

←

Stop Response Message }

0x7D

Special character sent to the I²C/SPI

driver to mark the end of a Response Mes-

sage.

←

Protocol error

0x21

For signalling.



Reports to the AT interface that the Trans-

fer Frame does not comply with the proto-

col definition (syntax error).

←

Transmission OK



(in I²C protocol referred to

as ACK)

0x2B

Notifies the AT interface that data were

successfully transmitted or, on the I²C bus,

the I²C Slave Address was recognized.

On I²C bus only:

←

Transmission error



(in I²C protocol referred to

as NAK)

0x2D

Notifies the AT interface that data trans-

mission failed or the I²C Slave Address

was not recognized. On the I²C bus, the

faulty data byte (16 bit byte counter) is

identified as well.

Содержание Cinterion EHS6


































































































































































































































































































































































































































































































































Результаты поиска

Содержание Cinterion EHS6

Отзывы:

Похожие инструкции для Cinterion EHS6

Бренды по названию

Популярные бренды

Gemalto Cinterion EHS6, Руководство по управлению

Результаты поиска

Содержание Cinterion EHS6

Отзывы:

Похожие инструкции для Cinterion EHS6

Бренды по названию

Популярные бренды