background image

GENERAL INFORMATION

Decal Locations information is provided to assist in the
proper selection and application of new decals, in the
event the original decal(s) become(s) damaged or the
machine is repainted.

For correct replacement of decal(s) compare the loca-
tion illustrations to your machine BEFORE starting to
refinish the unit. Check-off each required decal using
the illustration reference number to find the part num-
ber, description and quantity in the list. Refer to the
appropriate illustration(s) for replacement location(s).

NOTE:

Refer to the Safety chapter of this manu-

al for the specific information provided on all the
various safety decals.

NEW DECAL APPLICATION

Before applying the new decals, surfaces MUST be
free from dirt, dust, grease and other foreign material.
To apply a solid-formed decal, remove the smaller por-
tion of the decal backing paper and apply this part of
the exposed adhesive backing to the clean surface
while maintaining proper position and alignment.
Slowly peel off the other portion of the backing paper
while applying hand pressure to smooth-out decal sur-
face. to apply a die-cut decal, first remove the backing
paper. Then, properly orient and position the decal onto
the clean mounting surface. After the decal is firmly
applied and smoothly pressed down, remove the front
covering paper.

PAINT FINISH

Use this list to order paint for refinishing:

906213

One Gal. Yellow

906317

One Gal. Charcoal Grey

906323

One Qt. Charcoal Grey

906214

6 (12 oz. Spray Cans) Yellow

906318

6 (12 oz. Spray Cans) Charcoal Grey

L98622

1 (12 oz. Spray Can) Yellow

L98623

1 (12 oz. Spray Can) Charcoal Grey

COMPLETE DECAL KITS

L700528

Model 1639

L700529

Model 1649

NOTE: Decals can also be ordered individually.

Chapter 10

DECAL LOCATIONS

CAUTION

ALWAYS read and abide by the Safety Rules
and information shown on Decals. If any
Decal(s) become(s) damaged, unreadable or if
the unit is repainted, the Decal(s) MUST be
replaced. If repainting, MAKE SURE that ALL
Decals which apply to your machine are
affixed in their proper locations.

907389/AP297

58

Printed In U.S.A.

Discount-Equipment.com

Содержание PowerBox 1639



































































Отзывы: