Gehl CTL60 Скачать руководство пользователя страница 78 | Manualshive

Страница: 78 / 170

Gehl CTL60 Скачать руководство пользователя страница 78

76

OPERATION

T7D0371

T7D0381

T7D0391

Operations Possible with this Machine

IMPORTANT: Do not perform scooping or grading operations with the bucket cylinders
fully extended. The traction force will apply extremely heavy loads on the bucket
cylinders and this may damage them.

Scooping

Lower the lift arms and bring the bucket down to the ground with the front end tilted slightly
forward, then drive the loader forward until the bucket is filled with the material. Next tilt the
bucket backward and scoop up the material.

Grading

Tilt the front edge of the bucket down at an angle which is appropriate for the ground hardness,
then drive the loader forward slowly, digging into the ground with the cutting edge of the
bucket. When the bucket is full, tilt it backward.

Leveling

Raise the lift arms and tilt the bucket forward, then release it as the loader is driven forward.
Next tilt the bucket forward and lower the front edge until it is slightly above the ground
surface, then back the loader over the load which was just released.

Operating Procedures

«
...
76
77
78
79
80
...
»

Содержание CTL60











































































































































































Отзывы:

Нет отзывов