manualshive.com logo in svg

Gehl CTL60, Руководство оператора, Страница: 72 / 170

Поделиться
Скачать
Gehl CTL60 Скачать руководство пользователя страница 72

70

OPERATION

Operating Procedures

Prohibited Operations

 WARNING

¡

¡

¡

¡

¡

Do not operate on base rock (hard or
soft).

¡

¡

¡

¡

¡

If you must operate the lift arms and
bucket while traveling, operate at
speeds slow enough so you have
complete control at all times.

¡

Work should not be performed on a slope
since the balance of the machine can be
lost when operating the working
equipment and there is the danger of the
machine tipping over.

¡

Keep the bucket as low as possible during
travel. Do not travel or attempt to change
directions with the bucket raised.

¡

Travel at a speed which is appropriate for
the conditions. Travel at low speed when
the field of view is obstructed and take
extra precautions with hazardous
materials.

¡

Do not use this loader in areas where there
is danger of explosion from volatile gases.
Also avoid using the loader where the
exhaust gases could come in contact with
flammable items.

T7D021

T7D022

T7D023

6%, "

Содержание CTL60











































































































































































Отзывы:

Нет отзывов