Gehl CTL60 Скачать руководство пользователя страница 65

Страница: 65 / 170

OPERATION

Machine Operation

Warming Up the Hydraulics

WARNING

Operating the working equipment without
warming up the hydraulics is dangerous,
as response will be slow and the
equipment may move in unexpected
ways. Be sure to sufficiently warm up the
hydraulics.

IMPORTANT: Do not operate the levers
suddenly when the hydraulic oil
temperature is below 20

C (68

F). The

proper hydraulic oil temperature during
operation is 50 to 80

C (122 to 176

F), but

if operations must be performed at lower
temperatures, heat up the hydraulic oil
to at least 20

C (68

F).

Normal Warm-up

1. Run the engine at medium speed for about

5 minutes with no load.

2. Set the safety bar to the released position

and lift the bucket from the ground.

3. Extend and retract each of the cylinders

several times with no load.

4. Travel slowly forward and backward

several times.

Warming Up in Cold Weather
1. Perform the normal warm-up procedure.

2. Set the bucket cylinder at the stroke end

and keep it there.
Do not do this for more than 30 seconds.

3. Repeat step 2 until the bucket operating

speed is normal.

T7D004

6%,&

6%,'

6%,

Содержание CTL60











































































































































































Результаты поиска

Содержание CTL60

Отзывы:

Gehl CTL60, Руководство оператора, Страница: 65 / 170

Результаты поиска

Содержание CTL60

Отзывы: