manualshive.com logo in svg

Gehl CTL60, Руководство оператора, Страница: 52 / 170

Поделиться
Скачать
Gehl CTL60 Скачать руководство пользователя страница 52

50

CONTROLS

Safety Bar

 WARNING

¡

¡

¡

¡

¡

Before leaving the operator’s seat,
raise the safety bar to engage the lock
and stop the engine.
If any controls should be touched
accidentally when the safety bar is
lowered, the machine will move
suddenly, and cause serious injury or
death.

¡

¡

¡

¡

¡

Be careful not to touch the control
levers and pedal when lowering or
raising the safety bar.

This device is for locking the control levers,
pedal and selector, detent mode and high
flow switches.
When the safety bar is lifted, then levers,
pedal and switches are locked.

Throttle Lever

This controls the engine speed.
(A) .......... Low idling
(B) .......... Maximum speed

Right Control Lever

 WARNING

Be careful to check which pattern of lever
control arrangement you are operating
with before beginning operations.

Use this lever to operate the lift arms and
bucket.

Refer to page 62 “Lever Pattern”.
Refer to page 68 “Operating the Right
Control Lever”.

Levers and Pedals

T7B015

A

B

T7B016

T7B017

Содержание CTL60











































































































































































Отзывы:

Нет отзывов