Gehl CTL60 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 170

Gehl CTL60 Скачать руководство пользователя страница 50

48

CONTROLS

Switches

Detent Mode Switch (D)

This switches the function of auxiliary
hydraulic switch (A). Normally auxiliary
hydraulic switch (A) is on while it is pressed
and turns off when it is released. If pressed
after pressing this switch, auxiliary hydraulic
switch (A) turns on and stays on when it is
pressed, and only turns off when it is pressed
again. The built-in lamp (orange) lights when
the switch is on. Thus there is no need to
hold the switch in. When this switch is
pressed again, the function of the auxiliary
hydraulic switch returns to normal and the
lamp turns off.

T9B014

If Equipped

T9B016

If Equipped

Travel Speed Switch

Press this switch to set the travel speed to
2nd speed (high speed) while travel speed
lamp lights. Press again to return to 1st speed
(low speed) and travel speed lamp turns off.
Travel speed is always begin at 1st speed
when starting the engine.
Refer to page 45 “Travel Speed Lamp”.

«
...
48
49
50
51
52
...
»

Содержание CTL60











































































































































































Отзывы:

Нет отзывов