Gehl CTL60 Скачать руководство пользователя страница 128 | Manualshive

Страница: 128 / 170

Gehl CTL60 Скачать руководство пользователя страница 128

126

MAINTENANCE

When Required

Replacing the Bucket or
Attachment

WARNING

Before performing maintenance or
repairs under the machine, set all working
equipment against the ground or in the
lowermost position.

Installation

IMPORTANT: Read the manufacturer’s
instructions manual for attachments not
included in this manual. DO NOT use
attachments that are not approved by
Gehl.
IMPORTANT: Before installing a bucket
or attachment, make sure the mounting
area of the bucket (1) and the quick
attachment (3) are clean.

1. Make sure the quick attachment (3) lock

levers (2) are in the unlocked position.

2. While sitting in the operator’s seat with the

safety bar down, start the engine and tilt
the quick attachment (3) forward.

3. Move the machine slowly forward and

raise the loader lift arms. The wedge
shaped top edge of the quick attachment
(3) must engage in the upper mounts of
the bucket or attachment.

4. Roll the quick attachment (3) back while

lifting the bucket or attachment off the
ground. The quick attachment (3) will slide
into position.

5. Lower the bucket or attachment until it is

25 to 50 mm (1 to 2 in.) off the ground.

6. Stop the engine and raise the safety bar.

7. Push both quick attachment (3) lock levers

(2) down securing the bucket or
attachment in position.

T9G009

1

3

2

1

3

T9G010

T9G011

1

3

T9G012

4

2

3

«
...
126
127
128
129
130
...
»

Содержание CTL60











































































































































































Отзывы:

Нет отзывов