gefran AD Скачать руководство пользователя страница 71

Страница: 71 / 142

ADV200 WA • Quick start up guide - Specification and installation

7.1 Startup Wizard

7.1.1 Startup Wizard for Asynchronous Motors

Introduction

The ADV200 WA can operate with regulation modes : V/f control (Voltage/Fre-

quency) and Flux vector OL (open loop).

Menu 04 DRIVE CONFIG, parameter 04.2

Regulation mode

, PAR: 552, default=V/f

control.

Start-up in one mode is valid also for the other regulation modes.

The startup wizard is a guided procedure used for quick start-up of the drive that

helps to set the main parameters.

It consists of a series of questions relating to the various sequences for entering

and calculating the parameters necessary for correct drive operation.

The order of these sequences is as follows:

● Basic connections

See

step 1

●

Setting motor parameters

See

step 2

●

Self-tuning with rotating motor

See

step 3A

●

Self-tuning with motor at stand-still or coupled to the load

See

step 3B

●

Setting the maximum speed reference value

See

step 4

●

Setting ramp parameters

See

step 5

●

Saving parameters

See

step 6

●

Speed regulation setting

See

step 7

●

Setting the motor in Flux vector OL control mode

See

step 8

The format of the function selection page is as follows:

T+

T-

LOC

ILim

n:0

01 MONITOR

02 DRIVE INFO

03 STARTUP WIZARD

04 DRIVE CONFIG

T+

T-

LOC

ILim

n:0

STARTUP WIZARD

Set motor data ?

E=Yes

Down=Next

Pressing the E key, the function to be programmed is accessed.

Press the ▼ (Down) key to move to the next function skipping the current function.

Press the ▲ key to return to the previous function.

To terminate the sequence of functions and return to the menu, press the

ESC

key.

The end of the start-up sequence is indicated with the page:

T+

T-

LOC

ILim

n:0

STARTUP WIZARD

End of sequence !

Up=Back

Down=Next

Press the ▼(Down) key to exit the sequence and return to the menu.

Note !

In the procedures described below, the settings have been made using the ADV2075 drive and a 10 Hp
(7.36 kW) asynchronous motor.

Содержание AD















































































































































Результаты поиска

Содержание AD

Отзывы:

Похожие инструкции для AD

Бренды по названию

Популярные бренды

gefran AD, Быстрый старт, технические характеристики и установка

Результаты поиска

Содержание AD

Отзывы:

Похожие инструкции для AD

Бренды по названию

Популярные бренды