gefran AD Скачать руководство пользователя страница 16

Страница: 16 / 142

ADV200 WA • Quick start up guide - Specification and installation

3.2 Permissible Environmental Conditions

Temperature

storage �� -25…+55°C (-13…+131°F), class 1K4 per EN50178

-20…+55°C (-4…+131°F), for devices with keypad

transport �� -25…+70°C (-13…+158°F), class 2K3 per EN50178

-20…+60°C (-4…+140°F), for devices with keypad

Air humidity

storage �� 5% to 95 %, 1 g/m

to 29 g/m

(class 1K3 as per EN50178)

transport �� 95 % (3), 60 g/m

(4)

A light condensation of moisture may occur for a short time occasionally if the device is not in operation

(class 2K3 as per EN50178)

Air pressure:

storage �� [kPa] 86 to 106 (class 1K4 as per EN50178)
transport �� [kPa] 70 to 106 (class 2K3 as per EN50178)

(3) Greatest relative air humidity occurs with the temperature @ 40°C (104°F) or if the temperature of the

device is brought suddenly from -25 ...+30°C (-13°...+86°F).

(4) Greatest absolute air humidity if the device is brought suddenly from 70...15°C (158°...59°F).

The drive is suitable for use under the environmental service conditions (climate,

mechanical, pollution, etc.) defined as usual service conditions according to

EN61800-2.

Attention

Содержание AD















































































































































Результаты поиска

Содержание AD

Отзывы:

Похожие инструкции для AD

Бренды по названию

Популярные бренды

gefran AD, Быстрый старт, технические характеристики и установка

Результаты поиска

Содержание AD

Отзывы:

Похожие инструкции для AD

Бренды по названию

Популярные бренды