manualshive.com logo in svg

gefran 2850T, Инструкция по использованию и установке, Страница: 86 / 166

Поделиться
Скачать
gefran 2850T Скачать руководство пользователя страница 86

84

4. CONFIGURATION

80703B_MHW_2850T/3850T_02-2019_ENG

preconfigure sets of operating parameters that can 
easily be called up. The number of parameters available 
to groups is limited to those regarding PID control for 
heating and/or cooling. The parameters for all groups 
are overwritten at the end of the self-tuning process. 
The group will be set to 1 at the time of start-up.

• 

Man

: touch the key to enable or disable manual regula-

tion. The key turns green when on.

• 

P man

: percent power that can be set in manual mode.

This percentage remains identical to the automatic 
power when the PID is not in a manual mode. Otherwi-
se, it can be set. The PID_MAN_POW_n variables allow 
you to manage this parameter in GETlogic and GET-
view

• 

Antispike filter

: antispike filter representing the 

minimum duration of an ON or OFF impulse on digital 
outputs, measured in seconds. This parameter is not 
displayed if manual control or burst firing control (with 
CT set to 0) is enabled.

• 

Soft start

: enables gradual initial power distribution. If 

enabled (value other than 0), the next time the instru-
ment is turned on power will not be deliverable at 
100% right from start-up, but will follow a time ramp 
set in minutes. 
For example, set 10 minutes to achieve: 1 minute 
after turning on, maximum power will be 10%, after 
5 minutes it will be 50% and maximum power will be 
reached after 10 minutes. The power shown in the 
page PID cfg reveals the effective power delivered at 
that time on the physical outputs of the PID. The power 
calculated by the PID algorithm alone is available in the 
BASE2 page and in the PID_nn_MAN variables.

• 

Dead band

: Symmetric dead band around the SET-

POINT where the PID does not change power distrib-
uted (unless derivative action). The parameter is not 
displayed if manual regulation is enabled. Proportional 
band calculation is reconstructed on the basis of dead 
band. When we enter dead band, global control will 
also change slightly.

• 

Self T on

: touch the key to enable Self Tuning, mean-

ing a one-shot procedure to be run with start from 
room temperature. If there is a difference between PV 
and SETPOINT (in terms of absolute value) of greater 
or less than 5% of the bottom of the scale (HIS-LOS), 
self tuning cannot be activated. The key turns green 
when on. The parameter is not displayed if manual 
regulation is enabled. The Self Tuning process modifies 
the parameters of all 10 parameter groups. 
Self tuning consists of assessment of response to 
system step, calculating control parameters which 
optimise power delivery. The Self Tuning phase starts 
providing the max power untill the PV reaches a value 
in the middle between the starting value and the set-
point, than the power is switched off and it is evaluated 
the overshoot of the system.

• 

Sts

: self tuning status, indicated by a red LED when 

on. The parameter is not displayed if manual regulation 
is enabled. 
 

Power

 displays the percent power calculated at that 

time by the PID and if used for heating (red LED) or 
cooling (blue LED).

4.15.4.4.  PID limit configuration

The Base 3 page lets you set PID limits. 

The number of the PID being examined, which may be 
changed using the 

-

 and 

+

 buttons, appears at the top of 

the screen.
Turn the PID on and off with the 

EN

 button. The key turns 

green when the PID is enabled.

The value can be entered with the virtual keyboard by 
touching some parameters. The available parameters are:

• 

RATIO

: indicates the value of the ratio and is only 

displayed if Ratio operations were set in the Synoptic 
menu.

• 

SP

: Setpoint, value to be reached and maintained.

• 

PV

: Process value, current value (read only).

• 

Comma Red

: shows, in display only mode, PID pa-

rameters with one less decimal place than the Process 
Value variable.  Therefore, this operation does not 
affect controller precision. The key turns green when 
Comma Red is enabled.

• 

HIS

: Upper range limit.

• 

LOS

: Lower range limit.

• 

HIL

: Maximum settable set point.

• 

LOL

: Minimum settable set point.

• 

HPH

: Maximum power limit in heating.

• 

HPL

: Minimum power limit in heating.

• 

CPH

: Maximum power limit in cooling.

• 

CPL

: Minimum power limit in cooling.

Power

 displays the percent power calculated at that time 

by the PID and if used for heating (red LED) or cooling (blue 
LED).

Содержание 2850T







































































































































































Отзывы:

Нет отзывов