manualshive.com logo in svg

gefran 2850T, Инструкция по использованию и установке, Страница: 54 / 166

Поделиться
Скачать
gefran 2850T Скачать руководство пользователя страница 54

52

4. CONFIGURATION

80703B_MHW_2850T/3850T_02-2019_ENG

4.13.3.  Configuring the program

Configuring a program consists in defining all the param-
eters, functions, times, interactions with other programs 
and commands that characterise it and make it suitable for 
performing the task for which it is designed.

To configure an existing program, just select it from 
the PROGRAMS menu list, and then touch the button 

 to access the configuration pages.

The configuration procedure is developed through 4 sec-
tions (Base, Segments, GETlogic, Reports), each consisting 
of one or more configuration pages. Each page contains the 
name of the program.
If any changes have been made, the 

Save

 and 

Cancel

 

buttons appear on the pages in order to save the changes 
or cancel them. Touching these buttons also closes the 
configuration procedure.

4.13.3.1.  Base program configuration

This is the 

page (1)

 that appears when activating the pro-

gram configuration procedure.
To navigate to other pages in the Base section, just touch 
the corresponding number or select the page from the 
drop-down menu that appears by touching the "Base" label 

or by using keyboard keys 

 and 

.

BASE - page 1

Parameter

Description

Possible values

Program name

Program name.
Touching the field opens a pop-up window with 
which you can select another program. 

Alphanumeric string, max. 16 characters long. 
The name must be unique (duplicates are not 
allowed).
Characters allowed a ... z, A ... Z, 0 ... 9, _.

Number

Absolute program identification number

Automatic value.

Description

Extended program description. It is used to iden-
tify the program running on different pages.

Alphanumeric text. The maximum length of the 
text is 23 (model 2850T) or 30 (model 3850T) 
characters.

Time unit

It is the time base shared by all program seg-
ments. The active base is highlighted in green. To 
change, touch the time base you want to use.

m : s

 

= Minutes : Seconds

h : m

 

= Hours : Minutes

d : h

 

= Days : Hours

N° repetitions

Number of automatic program repetitions before 
it stops.
0 means the program runs one time and then 
stops; 1 means the program is run twice and 
then stops, and so on. A program can be run 
automatically up to 10,000 times.

0

...

9999

Start Mode

Select the reference value at program start (SP = 
PV or SP can be set).

Start from SP
Start from PV

Stop mode

Operating mode at the end of the program in 
END status.

DO off

:

Last step
Reset

Ready mode

Behaviour of outputs when the program switches 
from any state to READY.

Unchanged Out
DO off
Out = PV
Unchanged Out, DO off
Out = PV, DO off, PID disabled

Start state

Status when the controller is switched on.

The Run, Hold, and End modes are only active 
if the program was running (Run or Hold) when 
turned off, otherwise the program is always 
brought to the Ready state.

Ready
Run
Hold
End

NOTE 1 : Enable the PIDs associated with a profile when the profile starts, using the number in the PID column in the pro-
grammer’s BASE2 page as reference for association.
NOTE 2: If the PID operates a valve, it will not be possible to disable it at the end of the programme
NOTE 3 : Before it can start again, the PID must operate empty to reset the integral

Содержание 2850T







































































































































































Отзывы:

Нет отзывов