Gefen EXT-UHD600A-88 Скачать руководство пользователя страница 24

Страница: 24 / 232

page | 12

tting S

tar

ted

Installation

Network Configuration using Syner-G

1. Launch the Gefen Syner-G application.

Download the application here:

http://www.gefen.com/support/download.jsp

2. Select the matrix (EXT-UHD600A-88) from the list of products.

3. Under the Device Settings section, select either Static or DHCP from the IP Mode

drop-down list.

► Select

Static

to manual enter the IP address, subnet mask, and gateway IP.

Consult with your network administrator, if necessary.

► Select

DHCP

to let the DHCP server automatically assign the IP address, subnet

mask, and gateway IP.

tting S

tar

ted

Содержание EXT-UHD600A-88









































































































































































































































Результаты поиска

Содержание EXT-UHD600A-88

Отзывы:

Бренды по названию

Популярные бренды

Gefen EXT-UHD600A-88, Руководство пользователя

Результаты поиска

Содержание EXT-UHD600A-88

Отзывы:

Бренды по названию

Популярные бренды