Gefen EXT-UHD600-41 Скачать руководство пользователя страница 7

Страница: 7 / 136

vii

Features and Packing List

Features

•

Routes up to four Ultra Hi-Def sources to one Ultra HD display

•

Supports resolutions up to 4K DCI-Cinema (4096 x 2160 at 60 Hz, 4:4:4), 4K Ultra HD

(3860 x 2160 at 60Hz, 4:4:4), 1080p Full HD, & 1920x1200 (WUXGA)

•

Supports HDCP 2.2 and 1.4

•

Supports HDR (High Dynamic Range) 10-bit Deep Color at 4K 60 Hz 4:2:0 and 4K 24

Hz 4:4:4

•

Supports 12-bit Deep Color at 1080p 60 Hz 4:4:4

•

3DTV pass-through

•

Lip Sync pass-through

•

Advanced EDID and HDCP Management via Web Server Interface for rapid

integration of sources and display

•

Supports uncompressed LPCM digital audio up to 7.1 channels

•

Supports up to 7.1 channels of HBR (High Bit Rate) digital audio including Dolby

Atmos®, Dolby® TrueHD, DTS:X™, and DTS-HD Master Audio™

•

Supports the use of DVI sources and DVI displays up to 1080p Full HD and

1920x1200 (WUXGA), with HDMI-to-DVI adapters (not included)

•

Configurable Automatic Input Switching selects the most recent connected or

powered-up source

•

Front Panel Push button Input Selector routes one of the 4 connected sources to the

display, or “Blocks” (turns off) the input

•

RS-232 Serial interface for use with an automation control system

•

IP control via Telnet, UDP, and the built-in web server interface

•

IR remote control

•

Small surface-mountable IR Extender module allows the switcher to be hidden away

behind the display or in the equipment closet

•

Gefen Syner-G™ software’s Discovery and Show-Me features simplify initial IP

configuration

•

In-field firmware update via Web Server Interface

•

Long Reach Power (LRP) provides 500 mA at 5V on pin 18 of HDMI output. Enables

select extender devices to be powered through their HDMI input port

•

Locking power connector ensures reliable operation

•

Low-profile, surface-mountable enclosure can be surface mounted, placed on a shelf,

or hidden away behind the display

HDCP

2.2

60Hz, 4:4:4

600 MHz

4K ULTRA

High Dynamic Range

1080P

60Hz, 4:4:4

600 MHz

4K ULTRA

High Dynamic Range

Deep Color Support

CINEMA

DCI, 4096 x 2160, 30Hz

CINEMA

DCI, 4096 x 2160, 30Hz

Содержание EXT-UHD600-41









































































































































Результаты поиска

Содержание EXT-UHD600-41

Отзывы:

Похожие инструкции для EXT-UHD600-41

Бренды по названию

Популярные бренды

Gefen EXT-UHD600-41, Руководство пользователя

Результаты поиска

Содержание EXT-UHD600-41

Отзывы:

Похожие инструкции для EXT-UHD600-41

Бренды по названию

Популярные бренды