GEDA 300 Z Скачать руководство пользователя страница 90

Страница: 90 / 104

Malfunctions – diagnosis – repair

300 Z/ZP 2

BL144 GB 2019-11

5.2

Fault table

The following table lists potential malfunctions and the appropriate

remedial action.

Malfunctio

Cause

Remedial action

Green control light off

Mains plug disconnected

Connect the mains plug

Mains switch off

Switch on the main switch

Lamp defective

Replace lamp

Phase failure

Measure the phases

Incorrect phase sequence

Correct the phase sequence on

the phase sequence monitor

Travelling cable unplugged

Plug in the trailing cable

Fuses in the ground station

switch box not OK

Check/correction

Green control light

lights up

, platform does not move

EMERGENCY STOP

button (at

a control point) pressed

Unlock the

EMERGENCY STOP

button

Loading door/ramp open

Close loading door/ramp

Barrier with loading ramp open

Close barrier with loading ramp

Assembly guard plate open

Attach assembly guard plate at

the top

Assembly plank (if fitted) open

Close the assembly plank and

engage safety hook twice

EMERGENCY LIMIT

limit

switch activated

Refer to platform moved too

high/too low

Base enclosure barrier / sliding

door open (option)

Close the base enclosure

barrier / sliding door

Safety gear engaged

Release safety gear (see

chapter 5.3.5 Safety gear has

triggered)

Key switch on the platform

control switched to the incorrect

operating mode

Activate control using key

switch

Red control light lights up or pulsing signal tone sounds.

Overload protection has

triggered

Reduce the load

Platform only moves upwards

Is the

DOWN

limit switch

functioning properly

Check/replace the

DOWN

limit

switch

Содержание 300 Z









































































































Результаты поиска

Содержание 300 Z

Отзывы:

Похожие инструкции для 300 Z

Бренды по названию

Популярные бренды

GEDA 300 Z, Руководство по эксплуатации

Результаты поиска

Содержание 300 Z

Отзывы:

Похожие инструкции для 300 Z

Бренды по названию

Популярные бренды