GEA Omni Скачать руководство пользователя | Manualshive

Страница: 96 / 238

background image

2.14.2

Sensors Tab

fig.97:

Sensors tab display

This tab is used to adjust the range of sensors monitored by the panel. The table is divided into nine columns.
The leftmost column contains an icon that indicates whether the chosen point is an input or output. A green
arrow pointing to the right indicates that the point is an input, and a blue arrow pointing to the left indicates that
the point is an output. The remaining channels are detailed below.

1.

Channel

The text in this column indicates the slice number and channel that the chosen point occupies in the I/O sys-
tem.

2.

Description

This column contains the name of the chosen point.

3.

Min

This column contains the lowest allowable value for the chosen point during normal panel operation.

4.

Measured

This column contains the calibrated value read from or transmitted to the chosen point.

5.

Max

This column contains the highest allowable value for the chosen point during normal panel operation.

6.

Raw Scaled

This column contains the

Raw Signal

received by associated sensor scaled between the selected minimum

and maximum values.

7.

Offset

This column contains the value that is added to the reading displayed in the

Raw Scaled

column to obtain

the measured value for the sensor.

8.

Raw Signal

This column contains the unscaled value received by the sensor.

User interface
Configuration

Instruction Manual | GEA Omni™

Control panel

96

GEA Refrigeration North America, Inc. | E_806550_2 | Generated 12.01.2016

«
...
94
95
96
97
98
...
»

Содержание Omni















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Omni

Бренд: Balboa Instruments Страницы: 10

Бренд: Quantum Data Страницы: 36

Бренд: Ohsung Electronics Страницы: 18

Бренд: +GF+ Страницы: 3

Бренд: Össur Страницы: 58

Бренд: Nice Страницы: 120

Бренд: Seiko Страницы: 30

ASC G Wi-Fi kit

Бренд: Waeco Страницы: 386

Бренд: Motorline professional Страницы: 8

Бренд: Swagelok Страницы: 20

Бренд: V-ZUG Страницы: 24

Бренд: EBS Страницы: 118

IconRemote IR10A

Бренд: X10 Страницы: 21

Бренд: Rheem Страницы: 2

Бренд: Allen-Bradley Страницы: 88

Бренд: Grundfos Страницы: 12

NETBuilder II DPE 80

Бренд: 3Com Страницы: 32

Бренд: 4IPNET Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды