GEA Omni Скачать руководство пользователя | Manualshive

Страница: 79 / 238

background image

D Task Note

This field may be used to enter details relating to the completion of the selected task. The information
entered here will be displayed in the

Service Task

description section of the main display.

E Service Levels

This section contains check boxes corresponding to each service interval. Selecting a box will add the
custom task to the list of required tasks for the given interval. The

Check All

option is displayed above

the checkboxes, which will add the task to all service intervals. Clicking the option a second time will
remove the task from all service intervals.

The buttons shown at the bottom of the display are used to add, remove or change custom service tasks. The
buttons are:

F New Service Task

Touching this button will clear all fields and allow the user to enter the details of a new service task. The
user will be prompted to select a name for the task, which will automatically be added to the options in
the drop down list.

G Delete Service Task

This button is only enabled when a service task is selected in the drop down list. Touching it will erase
the service task currently selected in the drop down list.

H Save Service Task

This button is only enabled when a service task is selected in the drop down list. Touching it will create
or edit the selected service task based on the information entered in the fields.

4.

Edit Service Intervals

This button is used to modify the amount of time the compressor must run before each service interval
comes due. Touching it will bring up the dialog box displayed below. Any of the existing service intervals
may be selected using the drop down list on the left. The hours of the interval may be changed by enter-
ing the desired interval into the text box to the right and touching the

Save Service Change

button. If the

Ignore Service Notifications

option is checked, the panel will not annunciate notifications relating to serv-

ice intervals.

fig.82:

Service maintenance display

Instruction Manual | GEA Omni™
Control panel

User interface

Service

GEA Refrigeration North America, Inc. | E_806550_2 | Generated 12.01.2016

79

«
...
77
78
79
80
81
...
»

Содержание Omni















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Omni

Бренд: Waters Страницы: 55

Бренд: Paradox Страницы: 2

Бренд: Bartlett Страницы: 5

Бренд: YUGE Страницы: 69

Бренд: Quectel Страницы: 232

Бренд: Quectel Страницы: 9

Бренд: Quectel Страницы: 73

Бренд: Vaillant Страницы: 11

Бренд: Wang Страницы: 68

Бренд: NAVITAS Страницы: 14

Бренд: IDTECK Страницы: 12

Бренд: Banner Страницы: 2

CGLine+ Web Controller

Бренд: Eaton Страницы: 28

Бренд: Roger Страницы: 21

Бренд: Fluidmaster Страницы: 2

Бренд: Ezodo Страницы: 7

Saxun Mosquito Screen Lateral Door 2020

Бренд: Gimenez Ganga Страницы: 2

Бренд: Keysight Technologies Страницы: 78

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды