GEA Omni Скачать руководство пользователя | Manualshive

Страница: 223 / 238

background image

4.3

Notifications

4.3.1

List and Description of Compressor Notifications

Notification

Explanation

Upcoming Service Required
Notification

This annunciation will be triggered if the panel is scheduled for maintenance
within one hundred hours, as entered on the

Maintenance

chart in the

Serv-

ice

screen. This annunciation will only trigger if the compressor has been

running for at least five hundred hours. This notification will not be annunci-
ated if service notifications have been disabled.

Past Due Service Required
Notification

This annunciation will be triggered if the current service interval has not been
marked as complete and one hundred hours have passed since the interval
in question came due. If this notification is cleared, the panel will wait for the
compressor to run for another one hundred hours and, if the service interval
still has not been completed, will annunciate the notification again. The notifi-
cation will continue to be annunciated in one hundred hour increments until
the service interval is marked as completed. This notification will not be
annunciated if service notifications have been disabled.

Service Required Notification

This annunciation will be triggered once the runtime of the panel has reached
the next required service interval, as entered on the

Maintenance

chart in the

Service

screen. This notification will not be annunciated if service notifica-

tions have been disabled.

4.3.2

List and Description of Condenser Notifications

Notification

Explanation

Condenser Illegal Interlock

This annunciation will be triggered if the run status for a condenser device
becomes energized while the sequencing schedule indicates it should not be
running.

Detected Invalid Entries In Con-
denser Schedule

This annunciation will be triggered if the action selected for a condenser
device in the sequencing schedule is not a valid command for that type of
device.

Instruction Manual | GEA Omni™
Control panel

Annunciations

Notifications

GEA Refrigeration North America, Inc. | E_806550_2 | Generated 12.01.2016

223

«
...
221
222
223
224
225
...
»

Содержание Omni















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Omni

Бренд: Rayrun Страницы: 2

Бренд: IDenticard Страницы: 2

Бренд: 3Ware Страницы: 2

Бренд: 3M Страницы: 34

Бренд: Ebyte Страницы: 35

Бренд: J3C Страницы: 2

Бренд: Samson Страницы: 20

Бренд: Ascon tecnologic Страницы: 16

Бренд: KIOUR Страницы: 3

Бренд: Topway Страницы: 14

Бренд: Wave Home Solutions Страницы: 15

Бренд: Fuji Electric Страницы: 12

Бренд: heat-timer Страницы: 36

Бренд: Fagor Страницы: 8

MultiConnect Dragonfly MTQ-MNA1-B01

Бренд: Multitech Страницы: 45

Devicenet R7F4HD-DAC32C

Бренд: M-system Страницы: 9

Бренд: Universal Remote Страницы: 10

Бренд: Nanjing Putian Datang Information Electronics Co., Ltd. Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды