manualshive.com logo in svg

GEA Hilge HYGIA ADAPTA, Руководство по эксплуатации

Поделиться
Скачать
GEA Hilge HYGIA ADAPTA Скачать руководство пользователя страница 70

10.4.11 Determining gap size on HYGIA

D

D


9D

ULD

QW

H

YD

ULD

QW

9D

WUL

DQ

WH

9D

ULD

QW

E

Fig.63:

Gap size on HYGIA

General

The gap size needs to be determined only if modifying/replacing the impeller or
the ring housing. The gap between the impeller and the annular casing
contributes crucially to complying with the intended use. In the case of pumps
with a free-flow impeller, it is not necessary to determine the gap size. Such
pumps have a larger gap by design, which does not have to be adjusted exactly.
Two versions are described below.

Version 1 – Conical spring mechanical seal with seal spacer
Variant 2 - encapsulated (hygienic) mechanical seal

Preparation

1.

Remove the feather key (0940.00) from the shaft (0211.00).

2.

Remove the mechanical seal (0433.00) and the O-rings (0412.00) and
(0412.05).
→ Done.

Determining the air gap (a or a')
Version 1 – Conical spring mechanical seal with seal spacer

1.

Push the seal spacer (0557.00) onto the shaft (0211.00) as far as it will go.

2.

Push the impeller (0230.00) onto the shaft (0211.00), making sure it does not
contact the seal spacer (0557.00). It should be flush with the shaft thread at
the front.

Malfunctions / repairs

Repair

 

BA.H2A.ADY.002.GB_1

70

18.12.2017

Содержание Hilge HYGIA ADAPTA

































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды