GEA Hilge CONTRA I ADAPTA Скачать руководство пользователя страница 72

Страница: 72 / 96

10.4.11 Fasten discharge casing - simple mechanical seal

Equipment and tools from the GEA Hilge assembly tool kit

•

Loctite Type 243

•

Klüber paste UH1 96-402

Fasten discharge casing

Coat tie bolts (0905.01) with Loctite type 243 and
screw in hand-tight (!) into the bearing housings or
motor stool.

Fig.62:

Tie bolts

Grease rear of the discharge casing (0107.00) with
Klüber paste.

Fig.63:

Discharge casing, rear

Push the discharge
casing (0107.00) over
the shaft (0211.00).

Fig.64:

Assembly screws for
CONTRA II

Fig.65:

Discharge casing and shaft

Use assembly screws when installing CONTRA II
so that the larger discharge casing (0107.00) of
CONTRA II is held in place. It will then not fall on
the shaft (0211.00) during assembly.

→ The discharge casing is fastened.

Malfunctions / repairs

Repair

BA.10A.ADY.001.GB_1

20.07.2018

Содержание Hilge CONTRA I ADAPTA

































































































Результаты поиска

Содержание Hilge CONTRA I ADAPTA

Отзывы:

Бренды по названию

Популярные бренды

GEA Hilge CONTRA I ADAPTA, Руководство по эксплуатации

Результаты поиска

Содержание Hilge CONTRA I ADAPTA

Отзывы:

Бренды по названию

Популярные бренды