manualshive.com logo in svg

GEA Hilge CONTRA I ADAPTA, Руководство по эксплуатации

Поделиться
Скачать
GEA Hilge CONTRA I ADAPTA Скачать руководство пользователя страница 45

8.4

SIP

SIP stands for sterilisation in place, in which the pump is sterilised with
superheated steam. For steam sterilization or sanitization, minimum
temperatures of 121 ° C (250 ° F) must be applied to all wetted surfaces. The
maximum permissible temperatures can be obtained from the section technical
data.
The pump must not be in operation during steam sterilisation. A cool-down period
of at least one hour is required after the SIP process.

8.5

Manual exterior cleaning

 

Notice

 

Danger due to cleaning agents.
► Follow the manufacturer's instructions when using cleaning agents.
► Wear safety glasses and gloves.
► Dispose of cleaning agent properly.
► Do not use a high-pressure water jet to clean the pumps.

–

Regular manual external cleaning of the pump unit facilitates proper
operation.

–

Always check the impermeability of the motor (terminal box, condensation
water holes) before each cleaning.

–

Clean the outside of the pump with a soft cloth or brush and use warm water if
necessary.

–

When using a cleaning agent, make sure that it does not attack the surface of
the pump unit.

–

Remove dust and debris that may clog the fan and cooling fins of the engine.

–

Dry cleaning is preferable to wet cleaning.

–

The cleaning intervals depend on the degree of contamination.

Cleaning

SIP

BA.10A.ADY.001.GB_1

 

20.07.2018

45

Содержание Hilge CONTRA I ADAPTA

































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды