GEA Futuro Скачать руководство пользователя страница 40

Страница: 40 / 108

Transport

Information on disposing of packing material

2007-9015-001
03-2014

40 / 108

4.4

Lifting and moving the pump

Using safety chains

● Attach safety chains to the lifting

rings as illustrated below.

● To lift the pump in a vertical position,

use the lifting rings located on the
top of the pump.

4.5

Lifting and moving the hydraulic power unit

Using a fork lift

● Insert forks under the power unit

motor base to lift it.

4.6

Storage conditions

Attention!

Risk of corrosion!

When storing the goods supplied, the location must provide protection against:

● Moisture

● Frost

● External damage (jolts, knocks, rodents, insects, . . . )

● Direct sunlight

4.7

Information on disposing of packing material

After unpacking, the packing material is to be handled properly and disposed
of carefully in accordance with the valid local regulations on waste disposal and
utilization.

Содержание Futuro













































































































Результаты поиска

Содержание Futuro

Отзывы:

Похожие инструкции для Futuro

Бренды по названию

Популярные бренды

GEA Futuro, Инструкция по эксплуатации и руководство по установке

Результаты поиска

Содержание Futuro

Отзывы:

Похожие инструкции для Futuro

Бренды по названию

Популярные бренды