GEA Futuro Скачать руководство пользователя страница 21

Страница: 21 / 108

Description

Design of the equipment

2007-9015-001
03-2014

3.2

Changes to the product

Unauthorized modifications of the product can have a negative impact on the
safety, life span or functionality of the product.

Any modifications not described in the product documentation are deemed to
be prohibited.

For safety reasons, do not carry out any unauthorized modifications!

Planned changes must be approved by the manufacturer in writing.

Any unauthorized modifications to the product will invalidate the warranty and
may invalidate the provided manufacturer's declaration or installation
declaration.

3.3

Design of the equipment

Design

The pump consists of:

● A hydraulically powered vertical piston pump fixed on an evacuation

chamber based on double check valve principle.

Drive

● The piston pump is driven by a hydraulic power unit.

Содержание Futuro













































































































Результаты поиска

Содержание Futuro

Отзывы:

Бренды по названию

Популярные бренды

GEA Futuro, Инструкция по эксплуатации и руководство по установке

Результаты поиска

Содержание Futuro

Отзывы:

Бренды по названию

Популярные бренды